Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Teamson Home Jar 3 Tiered Floor Waterfall Fountain. Please read these instructions thoroughly before assembly and use, and retain them for future reference.
The fountain features a 3-tiered design with ceramic-look jars, constructed from durable, weatherproof, and rust-resistant polyresin. It is designed to create a soothing water flow for outdoor spaces such as porches, backyards, or lawns.
Safety Information
- Electrical Safety: Always connect the pump to a properly grounded outlet. Do not operate the pump if the power cord is damaged. Ensure the power cord is placed where it cannot be tripped over or damaged.
- Water Safety: Use only clean water in the fountain. Regularly check the water level to ensure the pump remains fully submerged. Never allow the pump to run dry, as this can cause damage.
- Placement: Place the fountain on a level, stable surface to prevent tipping. Ensure it is positioned away from areas where children or pets might accidentally knock it over.
- Assembly: Do not attempt to modify the fountain or its components. Use only the provided parts for assembly.
- Winterization: In freezing temperatures, drain all water from the fountain and store the pump indoors to prevent damage.
Package Contents
Verify that all components are present before beginning assembly:
- Fountain Body (3-tiered jar structure)
- Water Pump with power cord
- Assembly Instruction Manual
Figure 1: Fountain body and water pump as included in the package.
Setup Instructions
- Unpack Components: Carefully remove all parts from the packaging and place them on a soft, clean surface to avoid scratches.
- Position the Fountain: Choose a level and stable location for your fountain. Ensure it is near a grounded electrical outlet and away from high-traffic areas.
- Connect the Pump: Locate the water pump. Connect the pump's tubing to the water inlet hose inside the fountain body. Ensure a secure connection.
- Place the Pump: Position the pump at the bottom of the lowest basin within the fountain structure.
- Fill with Water: Fill the fountain with distilled or clean tap water until the pump is fully submerged. Do not overfill.
- Plug In: Carefully route the power cord to the electrical outlet, ensuring it does not create a tripping hazard. Plug the fountain into a grounded electrical outlet.
Figure 2: Assembled fountain in an outdoor setting.
Figure 3: Water pump and connection accessories.
Operating Instructions
- Initial Start-up: After filling the fountain with water and plugging it in, the pump will begin circulating water. It may take a few moments for the water to flow consistently through all tiers.
- Water Level: Regularly check the water level. Due to evaporation, especially in warm or windy conditions, water levels will decrease. Refill as needed to keep the pump fully submerged.
- Adjusting Flow: Some pumps may have an adjustable flow rate switch. If present, adjust to your desired water flow.
- Turning Off: To turn off the fountain, simply unplug the power cord from the electrical outlet.
Figure 4: Water flowing from the top basin.
Maintenance
- Regular Cleaning: To prevent mineral buildup and algae growth, clean the fountain regularly. Drain the water, wipe down surfaces with a soft cloth and mild soap, then rinse thoroughly.
- Pump Cleaning: Periodically clean the pump to ensure optimal performance. Unplug the pump, disconnect it from the tubing, and remove any debris from the intake screen and impeller.
- Water Replacement: Replace the water in the fountain every 1-2 weeks, or more frequently if it appears dirty or cloudy.
- Winter Storage: Before the first frost, drain all water from the fountain. Clean the fountain and pump, then store them in a dry, frost-free location.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fountain not working | Not plugged in; no power; low water level; clogged pump. | Ensure power cord is securely plugged in. Check power outlet. Add water until pump is submerged. Clean pump intake. |
| Water flow is weak | Low water level; clogged pump; kinked tubing. | Add water. Clean pump and tubing. Straighten any kinks in the tubing. |
| Excessive splashing | Water level too high; pump flow too strong; uneven surface. | Reduce water level slightly. Adjust pump flow rate if possible. Ensure fountain is on a level surface. |
| Water leaking | Cracked basin; improper assembly; uneven surface. | Inspect fountain for cracks. Reassemble carefully, ensuring all connections are tight. Place on a perfectly level surface. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | B01BEUIR4A |
| Brand | Teamson Home |
| Material | Resin |
| Color | Vintage Red |
| Product Dimensions (L x W x H) | 14.57" x 13.78" x 20.47" |
| Item Weight | 9.92 Pounds |
| Power Source | Corded Electric |
| Special Feature | Weather Resistant |
Figure 5: Fountain dimensions.
Warranty and Support
This product comes with a 30-day warranty against manufacturer defects. For any issues or support inquiries, please contact Teamson Home customer service. Refer to your purchase documentation for specific contact details.
