Introduction
This manual provides comprehensive instructions for the safe and effective use of your BLACK+DECKER 18V Cordless Grass Trimmer, model ST1823. This efficient cutting system ensures a clean edge cut and can easily manage larger lawn areas. Please read this manual thoroughly before operating the trimmer and keep it for future reference.
Figure 1: Overview of the BLACK+DECKER 18V Cordless Grass Trimmer ST1823.
Safety Information
WARNING: This product can produce flying debris, posing a potential injury risk. Always wear protective clothing, including safety glasses, and ensure others are not in the immediate vicinity. Do not touch the cutting area immediately after operation. This product is not a toy and should be kept out of reach of children. Always follow manufacturer instructions for proper usage and maintenance.
- Always wear appropriate personal protective equipment, including eye protection, long pants, and sturdy footwear.
- Keep bystanders, especially children and pets, at least 15 meters (50 feet) away from the operating area.
- Inspect the work area for objects that could be thrown or entangled in the cutting line.
- Do not operate the trimmer in wet conditions or rain.
- Ensure the battery is fully charged before use and remove it when not in use or during maintenance.
- Never modify the trimmer or use non-approved attachments.
Setup
1. Charging the Battery
Before first use, the battery must be charged. The battery may become warm while charging; this is normal and does not indicate a problem. The battery will not charge at ambient temperatures below 10°C or above 40°C. Recommended charging temperature range: 24°C.
Insert the battery pack into the appropriate outlet before inserting the battery pack into the charger. Plug the charger into an appropriate outlet. The green LED will flash, indicating that the battery is being charged. The completion of charge is indicated by the green LED remaining on continuously. The pack is fully charged and may be used at this time or left in the charger.
Warning: Recharged discharged batteries as soon as possible after use or battery life may be greatly diminished.
Figure 2: Inserting the 18V Lithium-Ion battery into the trimmer handle.
2. Assembly (if required)
Your trimmer may require minor assembly. Ensure all components are securely fastened before operation. Refer to the diagrams in the packaging for specific assembly steps. The handle can be adjusted for comfortable operation.
Figure 3: Adjusting the trimmer handle for optimal comfort and control.
Operating Instructions
1. Starting and Stopping
To start the trimmer, ensure the battery is fully inserted. Press and hold the safety lock-off button, then squeeze the trigger switch. To stop the trimmer, release the trigger switch.
2. Trimming Techniques
Hold the trimmer firmly with both hands. Maintain a comfortable stance. Swing the trimmer from side to side, keeping the cutting head slightly above the ground. For best results, cut only a small amount of grass with each pass. The AFS Reflex Fadenverlängerung (Automatic Line Feed System) automatically feeds the cutting line as needed.
Figure 4: Demonstrating proper trimming technique in a grassy area.
Figure 5: Using the trimmer for precise edging around garden beds.
Figure 6: Detail of the trimmer head cutting grass.
Maintenance
1. Cleaning
After each use, disconnect the battery and clean the trimmer housing with a damp cloth. Remove any grass clippings or debris from the cutting head and guard. Do not use harsh chemicals or abrasive cleaners.
2. Line Replacement
When the cutting line runs out, it needs to be replaced. Refer to the troubleshooting section for instructions on how to replace the spool and line. Always use genuine BLACK+DECKER replacement spools to ensure optimal performance.
Troubleshooting
Refer to the table below for common issues and their solutions.
| Problem | Solution |
|---|---|
| Appliance runs slowly. | Remove battery from trimmer. Check that the spool housing can rotate freely. Manually clean if necessary. Check that the cutting line does not protrude more than approximately 122 mm from the spool. If it does, cut it off so that it just reaches the line trimming blade. |
| Automatic line feed does not feed line. | More line is fed when the line shortens to approximately 70 mm. To determine if the line is not feeding, let line wear past this point. Keep the tabs depressed and remove the spool cap from the spool. Push the spool housing in the trimmer head. Ensure that the line is not crisscrossed on the spool as detailed in (Fig. Q). If it is, unwind the cutting line and rewind it neatly. Inspect tracks at the bottom of spool for damage. If damaged, replace spool. Pull the cutting line until it protrudes approximately 122 mm from the spool. If unable to pull the line out, remove the spool, install a new spool of cutting line. Align the tabs on the spool cap with the slots in the spool housing. Push the spool cap onto the housing until it clicks securely into place. If the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade. If the automatic line feed still does not work or the spool is damaged, install a new spool. Carefully clean the spool and housing. Make sure you are using correct line size. Using different line sizes, or smaller and larger line sizes will affect the performance of the trimmer. Remove the spool and check if the lever in the spool housing can move freely. If the lever is stuck, remove the cutting line, then wind it on neatly again. Replace the spool into the housing. |
| Overfeeding | Ensure you are cutting with the tip of the line, not from the spool. Use the edge guide if needed to ensure proper spacing is maintained. Ensure the line is not exceeding a 10° angle as shown (Fig. G1). |
| Line unravels when cap or spool is removed | Make sure to park the lines in holding slots (Fig. L) before removing. |
Figure 7: Excerpt from the original manual detailing battery charging and troubleshooting.
Specifications
- Brand: BLACK+DECKER
- Model Number: ST1823
- Power Source: Battery Powered
- Battery Type: 18V Lithium Ion (1 included)
- Battery Average Life: 45 minutes
- Cutting Width: 25 Centimeters
- Speed: 9000 RPM
- Item Weight: 4.41 Pounds (2 kg)
- Color: Black / Orange
- Cordless: Yes
- Manufacturer Part Number: ST1823-QW
Warranty and Support
BLACK+DECKER products are manufactured to high quality standards and are guaranteed for a period of 24 months from the date of purchase against faulty materials or workmanship. This guarantee does not affect your statutory rights. For warranty claims or technical support, please contact your local BLACK+DECKER service center or visit the official BLACK+DECKER website. Please have your model number (ST1823) and proof of purchase available when contacting support.
For additional information and to register your product, please visit: www.blackanddecker.com