Important Safety Instructions
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
- Read all instructions before using this heater.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles when moving this heater.
- Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
- Always unplug heater when not in use.
- Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
- Do not use outdoors.
- This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
- To disconnect heater, turn controls to OFF, then remove plug from outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable vapors or liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
Product Overview
The MIDEA Westpointe Oil-Filled Radiator Heater is designed to provide efficient and quiet warmth for your living spaces. Its oil-filled design ensures consistent heat distribution, while the integrated thermostat allows for precise temperature control. The unit is equipped with wheels for easy portability and a built-in cord storage for convenience.
Image: Front view of the MIDEA Westpointe Oil-Filled Radiator Heater. It is black, with a control panel featuring two rotary knobs and an indicator light. The heater stands on four caster wheels for easy movement, and the power cord can be stored at the base.
Key Features:
- Oil-filled radiator for stable and quiet heat.
- Three heat settings: 600W, 900W, and 1500W.
- Adjustable thermostat for personalized comfort.
- Convenient caster wheels for portability.
- Built-in cord storage.
- ETL approved for safety.
Setup & Assembly
Unpacking:
Carefully remove the heater from its packaging. Retain the packaging for off-season storage.
Attaching the Wheels:
- Invert the heater carefully to access the base.
- Locate the wheel brackets and align them with the designated slots at the bottom of the heater.
- Insert the wheels into the brackets. Ensure they click securely into place.
- Return the heater to an upright position.
Placement:
Place the heater on a firm, level surface. Ensure there is at least 3 feet (0.9 meters) of clearance from walls, furniture, and other objects to allow for proper air circulation and prevent fire hazards. Do not place the heater directly under a power outlet.
Operating Instructions
Powering On:
- Ensure the heater is properly assembled and placed.
- Plug the power cord into a grounded 120V AC electrical outlet.
- Turn the thermostat knob (usually the larger one) to the maximum setting.
- Turn the power setting knob (usually the smaller one) to your desired heat output:
- I (Low): 600 Watts
- II (Medium): 900 Watts
- III (High): 1500 Watts
- The power indicator light will illuminate when the heater is on.
Adjusting the Thermostat:
Once the room reaches your desired temperature, slowly turn the thermostat knob counter-clockwise until the heater turns off. The heater will now cycle on and off to maintain this temperature. For continuous heat, set the thermostat to its maximum setting.
Safety Features:
- Overheat Protection: The heater will automatically shut off if it overheats. Unplug the heater, allow it to cool for 30 minutes, and then plug it back in. If it continues to shut off, contact customer service.
- Tip-Over Switch: The heater is equipped with a safety switch that automatically turns the unit off if it is accidentally tipped over. Place the heater upright on a flat surface to resume operation.
Powering Off:
Turn the power setting knob to the "OFF" position. Unplug the heater from the wall outlet when not in use for extended periods.
Maintenance
Cleaning:
- Always unplug the heater from the wall outlet and allow it to cool completely before cleaning.
- Wipe the exterior surfaces of the heater with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Do not immerse the heater in water or allow water to drip into the interior of the heater.
- Clean the air intake and exhaust vents regularly with a vacuum cleaner attachment to remove dust and lint.
Storage:
When storing the heater, ensure it is completely cool and dry. Utilize the built-in cord storage to wrap the power cord neatly. Store the heater in a cool, dry place, preferably in its original packaging, to protect it from dust and damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater does not turn on. | No power to the unit; Power switch is off; Thermostat set too low; Overheat protection activated; Tip-over switch activated. | Check if the power cord is securely plugged into a working outlet. Ensure the power setting knob is not in the "OFF" position. Turn the thermostat knob to a higher setting. Unplug, wait 30 mins, then replug. Ensure heater is upright on a flat surface. |
| Heater is on but not heating. | Thermostat set too low; Room temperature is higher than thermostat setting. | Increase the thermostat setting. The heater will only activate when the room temperature drops below the set temperature. |
| Heater shuts off unexpectedly. | Overheat protection activated; Tip-over switch activated. | Unplug the heater, allow it to cool for 30 minutes, then plug it back in. Ensure the heater is on a stable, flat surface and has proper clearance from obstructions. |
| Unusual noise or smell. | New unit smell (normal for first few uses); Dust accumulation; Internal malfunction. | A slight odor is normal for new heaters and will dissipate. Clean the heater as per maintenance instructions. If noise or smell persists or is strong, discontinue use and contact customer service. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | HO-0218HB |
| Brand | Midea |
| Product Type | Oil-Filled Radiator Heater |
| Heat Settings | 3 (600W, 900W, 1500W) |
| Heating Method | Radiation |
| Power Source | Corded Electric |
| Dimensions (L x W x H) | 13.78" x 9.84" x 25.79" (35 cm x 25 cm x 65.5 cm) |
| Weight | 19.32 lbs (8.76 kg) |
| Color | Black |
| Form Factor | Pedestal |
| Assembly Required | Yes |
| Certifications | ETL Approved |
Warranty & Support
Midea products are manufactured to the highest quality standards. For specific warranty information regarding your HO-0218HB Oil-Filled Radiator Heater, please refer to the warranty card included with your purchase or visit the official Midea website.
If you encounter any issues or have questions not covered in this manual, please contact Midea Customer Service. Have your model number and purchase information ready when contacting support.
You can find contact information and additional resources on the official Midea website: www.midea.com
