Introduction
Thank you for choosing the Convectair Allegro II 14" Convection Heater. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your heater. Please read this manual thoroughly before installation and use, and retain it for future reference.
Image: Front view of the Convectair Allegro II 14" Convection Heater. This image shows the sleek, satin white exterior of the heater, designed for wall mounting.
Important Safety Information
WARNING: To reduce the risk of fire, electric shock, or injury, observe the following:
- Read all instructions before installing or using this heater.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains, at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
- Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
- Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped, or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
- Do not use outdoors.
- This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
- To disconnect heater, turn controls to off, then remove plug from outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable vapors or liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
Setup and Installation
The Convectair Allegro II heater is designed for permanent wall-mount installation. Proper installation is crucial for safety and optimal performance. It is recommended that installation be performed by a qualified electrician.
Mounting Location
- Choose a wall location that allows for proper air circulation around the heater.
- Ensure there is sufficient clearance from combustible materials (refer to safety information).
- Avoid mounting directly below electrical outlets.
Electrical Connection
This heater operates on 240/208 Volts and has a power output of 1500/1125 Watts, drawing 6.25 Amps. Ensure your electrical circuit can safely support these requirements. The heater must be hardwired into a dedicated circuit according to local electrical codes.
Image: Convectair Allegro II heater installed on a wall. This image demonstrates the heater's discreet presence when mounted, blending into a modern room environment.
Operating Instructions
The Allegro II heater features an intuitive control panel for setting your desired temperature and operating mode.
Image: Digital control panel of the Convectair Allegro II heater. This close-up shows the blue backlit display indicating "21.0 °C" and buttons for Power, Mode, and Temperature adjustment (+/-).
Power On/Off
- Press the Power button (symbolized by a circle with a vertical line) to turn the heater on or off.
Setting Temperature
- Use the "+" and "-" buttons to adjust the desired temperature. The current set temperature will be displayed on the digital screen.
- The heater will automatically maintain the set temperature by cycling on and off.
Operating Modes
- Press the Mode button to cycle through available operating modes (e.g., Comfort, Eco, Frost Protection). Refer to the display for the active mode.
- Each mode is designed for different energy saving or comfort levels.
Maintenance
Regular maintenance ensures the longevity and efficient operation of your Convectair Allegro II heater.
Cleaning
- Always disconnect power to the heater before cleaning.
- Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Ensure the air intake and exhaust vents are free from dust and debris. Use a vacuum cleaner with a brush attachment to gently clean these areas.
- Do not spray liquids directly onto the heater.
Internal Components
Image: Internal heating element of the Convectair Allegro II. This image displays the robust, finned aluminum heating element responsible for efficient convection heating.
The internal heating element is designed for durability and does not require user maintenance. If you suspect an issue with internal components, contact a qualified service technician.
Troubleshooting
Before contacting customer support, please review the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater does not turn on. | No power supply; circuit breaker tripped; unit off. | Check electrical connection; reset circuit breaker; press power button on control panel. |
| Heater not producing enough heat. | Temperature setting too low; blocked air vents; room too large for heater capacity. | Increase temperature setting; clear any obstructions from vents; ensure heater is appropriately sized for the room. |
| Unusual noises or odors. | Dust accumulation; internal component issue. | Clean vents and exterior; if problem persists, disconnect power and contact service. |
| Display not working. | Power issue; internal fault. | Check power supply; if power is present and display remains off, contact service. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Convectair |
| Model Number | 7315-C15-FS |
| Special Feature | Noiseless |
| Form Factor | Pedestal (Note: Product is wall-mounted, "Pedestal" might refer to internal design or a misclassification in source data) |
| Mounting Type | Wall Mount (Inferred from images and reviews, overriding "Floor Mount" from specs if contradictory) |
| Room Type | Bedroom, Home Office, Living Room |
| Burner Type | Radiant (Note: Product title states "Convection Heater", this might be a misclassification in source data) |
| Heat Output | 1500 Watts |
| Amperage | 6.25 Amps |
| UPC | 774725005830 |
| Product Dimensions | 16.5 x 35.5 x 6.5 inches |
| Item Weight | 16.87 pounds |
| Power Source | Corded Electric (Hardwired) |
| Heating Method | Convection |
Note: Some specifications from the source data, such as "Form Factor: Pedestal" and "Burner type: Radiant", appear to contradict the product title "Convection Heater" and visual evidence of wall mounting. This manual prioritizes the product title and visual evidence for clarity.
Warranty and Support
For warranty information, technical support, or service inquiries, please contact Convectair customer service directly. Keep your purchase receipt and model number (7315-C15-FS) available when contacting support.
You can typically find contact details on the manufacturer's official website or within the product packaging.
