Product Overview
The Bennett Marine BEA3000 BOLT Adjustable Actuator is an electric linear motion actuator designed for marine applications, specifically for trim tab systems. It features an adjustable upper hinge and includes plug-and-play connectors for ease of installation. This actuator is engineered for reliable performance and is compatible with retrofit kits for Lenco electric and Bennett hydraulic systems.
Image: The Bennett Marine BEA3000 BOLT Adjustable Actuator, shown in its retail packaging, highlighting its adjustable upper hinge and plug-and-play connectors.
Setup and Installation
Proper installation of the BEA3000 BOLT Adjustable Actuator is crucial for optimal performance. Follow these general steps for mounting the actuator to your trim tab system.
- Prepare Mounting Surface: Ensure the mounting surface on the transom and the trim tab are clean and free of debris.
- Position the Actuator: Place the actuator in the desired position on the trim tab, typically starting with the center holes for alignment. The actuator should be positioned flush against the mounting surface.
- Mark Drill Holes: Using the actuator as a template, carefully mark the locations for drilling the mounting holes on both the trim tab and the transom.
- Drill Pilot Holes: Drill appropriate pilot holes at the marked locations. Ensure the drill bit size is suitable for the mounting hardware to prevent damage to the fiberglass or metal.
- Secure the Actuator: Attach the actuator to the trim tab and the transom using appropriate marine-grade fasteners. Ensure all connections are secure and watertight.
- Connect Wiring: Utilize the plug-and-play connectors to integrate the actuator into your boat's electrical system. Refer to your boat's wiring diagram for correct connections.
- Verify Operation: After installation, test the actuator's movement to ensure it extends and retracts smoothly and fully.
Video: This video demonstrates the installation process of the Bennett Marine BOLT Electric Actuator onto a boat's trim tab, including marking and securing the unit.
Operating Instructions
The Bennett Marine BEA3000 BOLT Actuator is designed for easy operation to adjust your boat's trim tabs. The actuator has a "traveling position" for transport and a deployed position for active use.
- Engaging for Use: To move the trim tab from its traveling position to an operational state, push up on the trim tab and remove the securing pin from the actuator. This allows the actuator to extend and retract freely.
- Adjusting Trim: Use your boat's trim tab control panel to extend or retract the actuator, thereby adjusting the angle of the trim tab. This allows for fine-tuning of the boat's running attitude for optimal performance and comfort.
- Returning to Traveling Position: When transporting the boat, retract the actuator fully and secure the trim tab in its upward position using the pin. This protects the actuator and trim tab from damage during transit.
Maintenance
Regular maintenance ensures the longevity and reliable operation of your Bennett Marine BEA3000 BOLT Actuator.
- Routine Inspection: Periodically inspect the actuator for any signs of wear, corrosion, or damage. Check all mounting hardware for tightness.
- Cleanliness: Keep the actuator clean, especially after use in saltwater environments. Rinse with fresh water to remove salt and debris.
- Lubrication: Consult the full product manual for specific lubrication requirements. Generally, moving parts may benefit from light lubrication with marine-grade grease or spray.
- Electrical Connections: Ensure all electrical connections are clean, dry, and secure to prevent intermittent operation or corrosion.
Troubleshooting
If you encounter issues with your BEA3000 BOLT Actuator, consider the following troubleshooting steps:
- Actuator Not Responding:
- Check all electrical connections for looseness or corrosion.
- Verify power supply to the trim tab system.
- Inspect the control switch for proper function.
- Slow or Erratic Movement:
- Ensure the actuator is free from obstructions.
- Check for any binding in the trim tab hinges.
- Inspect wiring for damage or inadequate gauge.
- Unusual Noises:
- Listen for the source of the noise to identify potential mechanical issues.
- Inspect for loose components or foreign objects.
If troubleshooting steps do not resolve the issue, contact Bennett Marine customer support or a qualified marine technician.
Specifications
| Brand | Bennett Marine |
| Model | BEA3000 |
| Item Weight | 3.5 pounds |
| Product Dimensions | 7.05 x 6.78 x 2.7 inches |
| Item Model Number | BEA3000 |
| Manufacturer Part Number | 1111 |
| Lift Type | Automatically, Off |
Warranty and Support
The Bennett Marine BEA3000 BOLT Adjustable Actuator comes with a Lifetime No-Hassle Warranty, applicable in the U.S. and Canada only. This warranty reflects our commitment to quality and customer satisfaction.
For customer support, technical assistance, or warranty claims, please refer to the official Bennett Marine website or contact their customer service department directly. Our legendary customer support team is available to assist you.
