Taylor Digital Wireless Indoor Comfort Level Thermometer and Hygrometer User Manual

Introduction

The Taylor Digital Indoor Comfort Level Thermometer and Hygrometer is designed to help you monitor and regulate the indoor environment of your home, office, greenhouse, nursery, or any indoor area. This device provides accurate readings of indoor temperature and humidity, along with a visual comfort level indicator. Its large, easy-to-read display and convenient features make it an essential tool for maintaining optimal indoor conditions.

Key features include:

• Digital display for room humidity percentage and indoor temperatures in °F or °C.
• Built-in clock for timekeeping.
• Daily maximum/minimum indoor temperature and humidity recall.
• Colorful 5-level humidity comfort level indicator for quick assessment.
• Large digits for enhanced visibility and at-a-glance readings.
• Operates on a 12 to 24-hour display period.

What's in the Box

• Taylor Digital Wireless Indoor Comfort Level Thermometer and Hygrometer (Single Display Black)

Note: 2 AAA batteries are required and not included.

Product Overview

Figure 1: Front View of the Device

Figure 2: Side View with Kickstand

Figure 3: Rear View with Battery Compartment

The device features a large LCD display on the front, showing time, temperature, humidity, and a comfort level gauge. The back includes a removable battery cover and buttons for settings. A built-in kickstand allows for convenient tabletop placement.

Setup

1. Battery Installation

1. Locate the battery compartment on the back of the unit.
2. Remove the battery compartment cover by sliding it downwards.
3. Insert two (2) AAA batteries (not included) into the compartment, ensuring correct polarity (+ and -).
4. Replace the battery compartment cover. The display should activate.

2. Placement

The Taylor Digital Thermometer and Hygrometer can be placed on a tabletop using its integrated kickstand or mounted on a wall.

• Tabletop Placement: Extend the kickstand on the back of the unit and place the device on a flat, stable surface.
• Wall Mounting:
  1. Select a location on a wall that is out of direct sunlight.
  2. Two screws or nails (not included) are required for mounting. Place the first screw approximately 2 ¾” below the point where the top of the thermometer will be positioned, leaving screw or nail head out approximately ¼”. Place the second screw or nail 8” below the first.
  3. Place the clock/thermometer over the screws or nails heads.

Figure 4: Wall Installation Tips

Important Exposure Considerations:

• Do not mount in direct sunlight, near a heat source, or near a large body of water as these situations could affect the proper air temperature reading.
• Mount securely and protected from the wind to prevent against any damage from being knocked off the mounting screw and falling to the ground.

Operating Instructions

1. Initial Display

Upon battery installation, the device will display the current time, indoor temperature, and humidity. The comfort level indicator will also show the current comfort zone.

Figure 5: Device Features

2. Setting Time and Temperature Unit

Refer to the buttons on the back of the unit (often labeled "SET" and "°C/°F").

• To Set Time: Press and hold the "SET" button until the time display begins to flash. Use the other button (often "UP" or "ADJ") to adjust the hour, then press "SET" to confirm and move to minutes. Repeat for minutes.
• To Change Temperature Unit: Press the "°C/°F" button to toggle between Celsius and Fahrenheit.

3. Min/Max Temperature and Humidity Recall

The device automatically records the minimum and maximum temperature and humidity readings over a 12 to 24-hour period.

• Press the "MIN/MAX" button (if available, or a multi-function button) to view the maximum recorded values.
• Press the button again to view the minimum recorded values.
• Press a third time to return to current readings.
• To clear the Min/Max memory, press and hold the "MIN/MAX" button while viewing the Min/Max values.

4. Comfort Level Indicator

The colorful 5-level indicator at the top of the display visually represents the current indoor comfort level based on humidity:

• Red (DRY): Indicates low humidity.
• Green (COMFORT): Indicates optimal humidity levels.
• Blue (WET): Indicates high humidity.

Maintenance

1. Cleaning

Wipe the unit with a soft, damp cloth. Do not use abrasive cleaners or immerse the unit in water.

2. Battery Replacement

When the display becomes dim or unresponsive, replace the batteries. Follow the battery installation steps in the Setup section. Always replace both batteries at the same time with new ones.

Dispose of old batteries responsibly according to local regulations.

Troubleshooting

Specifications

Figure 6: Product Dimensions

Figure 7: Key Specifications

Warranty and Support

For warranty information and customer support, please refer to the documentation included with your product or visit the official Taylor website. Keep your purchase receipt for warranty claims.

For further assistance, you may contact Taylor customer service directly.