HyperX Savage DDR4 Memory Module User Manual

Introduction

This manual provides essential information for the installation, operation, and maintenance of your HyperX Savage DDR4 memory modules. The HyperX Savage DDR4 memory is designed to complement Intel's 2, 4, 6, or 8 core processors, offering enhanced performance for tasks such as video editing, 3D rendering, gaming, and AI processing. These modules feature speeds up to 3000MHz and latencies of CL15, optimized for Intel's 100 series chipset and X99 chipset motherboards, supporting easy overclocking via XMP profiles.

Image: Front view of the HyperX Savage DDR4 memory module, showcasing its black heat spreader with the HyperX logo and Savage DDR4 branding.

Package Contents

Verify that your package contains the following items:

• 2 x HyperX Savage DDR4 Memory Modules (8GB each, 16GB Kit)

Setup and Installation

Before installing the memory modules, ensure your system is powered off and unplugged from the wall outlet. It is recommended to wear an anti-static wrist strap to prevent electrostatic discharge (ESD) damage to components.

1. Preparation

1. Compatibility Check: Confirm that your motherboard supports DDR4 DIMM memory modules and the specified speed (3000MHz). Refer to your motherboard's manual for details.
2. Power Off: Shut down your computer completely and disconnect the power cable.
3. Open Case: Open your computer's side panel to access the motherboard.

2. Module Installation

1. Locate DIMM Slots: Identify the DDR4 DIMM slots on your motherboard. Consult your motherboard manual for the correct slot configuration for dual-channel memory.
2. Open Clips: Gently push down the retention clips at both ends of the DIMM slot.
3. Align Module: Hold the memory module by its edges, avoiding contact with the gold pins. Align the notch on the module with the key in the DIMM slot.
4. Insert Module: Apply even pressure to both ends of the module until it seats firmly into the slot and the retention clips snap into place. Do not force the module.
5. Repeat: Install the second memory module into the corresponding slot as indicated by your motherboard manual.

Image: Angled view of the HyperX Savage DDR4 memory module, showing the heat spreader design and the gold contact pins.

3. Post-Installation

1. Close Case: Reattach the side panel of your computer case.
2. Reconnect Power: Plug the power cable back into your computer and power it on.

Operating Instructions

After physical installation, it is important to configure your system's BIOS/UEFI to utilize the full potential of your HyperX Savage DDR4 memory modules.

Enabling XMP Profile

HyperX Savage DDR4 memory modules come with built-in Intel XMP (Extreme Memory Profile) profiles. These profiles are optimized for Intel 100 series chipsets and X99 motherboards, allowing for easy overclocking without manual timing adjustments.

1. Access BIOS/UEFI: During system startup, repeatedly press the designated key (commonly DEL, F2, F10, or F12) to enter your motherboard's BIOS or UEFI settings. The specific key varies by motherboard manufacturer.
2. Locate XMP Setting: Navigate to the memory or overclocking section within the BIOS/UEFI. Look for an option related to 'XMP', 'DOCP', 'A-XMP', or 'Memory Profile'.
3. Enable Profile: Select the XMP profile (usually 'Profile 1' or 'Enabled') to automatically configure the memory to its rated speed (3000MHz) and timings (CL15) at 1.35V.
4. Save and Exit: Save the changes and exit the BIOS/UEFI. Your system will restart with the new memory settings applied.

If your system does not support XMP, the memory will operate at a default JEDEC speed, typically 2133MHz or 2400MHz, depending on your motherboard and CPU.

Maintenance

HyperX Savage DDR4 memory modules are designed for durability and reliability. Minimal maintenance is required to ensure optimal performance and longevity.

• Keep Clean: Periodically clean the interior of your computer case to prevent dust buildup on the memory modules and other components. Use compressed air to gently remove dust.
• Proper Handling: When handling memory modules, always hold them by the edges to avoid touching the gold contacts or the integrated circuits.
• Temperature Control: Ensure adequate airflow within your computer case to maintain optimal operating temperatures for all components, including memory.

Troubleshooting

If you encounter issues after installing your HyperX Savage DDR4 memory, consider the following troubleshooting steps:

• System Not Booting:
  • Ensure the memory modules are fully seated in their slots and the retention clips are locked.
  • Verify that your motherboard supports the installed memory type and speed.
  • Try booting with only one module installed to identify a potentially faulty module.
• Incorrect Speed Detected:
  • Access your BIOS/UEFI settings and ensure the XMP profile is enabled.
  • Update your motherboard's BIOS/UEFI to the latest version, as this can improve memory compatibility and stability.
• System Instability or Crashes:
  • Run a memory diagnostic tool (e.g., Windows Memory Diagnostic or MemTest86) to check for errors.
  • Ensure your power supply unit (PSU) provides sufficient and stable power to all components.
  • Check for proper cooling within your system to prevent overheating.

Specifications

Warranty and Support

HyperX Savage DDR4 memory modules are backed by a lifetime warranty, ensuring long-term reliability and peace of mind. Free technical support is also available to assist with any questions or issues you may encounter.

For warranty claims or technical assistance, please visit the official HyperX support website or contact their customer service. Keep your proof of purchase for warranty validation.

HyperX Support: www.hyperx.com/support