TC CP-40S Laser Distance Meter User Manual

Introduction

Thank you for purchasing the TC CP-40S Laser Distance Meter. This device is designed for precise and rapid measurement of distances, areas, and volumes. It is an ideal tool for various applications in construction, real estate, and other industries requiring accurate measurements. Please read this manual carefully before using the device to ensure safe and optimal operation.

Key Features:

• High accuracy with a wide measuring range up to 40 meters.
• Quick measurement of distance, area, and volume with a single button operation.
• Automatic calculation functions for area and volume.
• Indirect measurement using the Pythagorean theorem.
• Minimum/Maximum distance tracking.
• Easy addition and subtraction of measurements.
• Selectable measurement reference point (front or rear benchmark).
• Switchable units: meters (m), inches (in), and feet (ft).
• Bright laser pointer for easy targeting.
• Large LCD with backlight and multi-line display (4 lines).
• Automatic correction and error reporting technology.
• Low battery indication.
• Automatic and manual power-off functions.
• Compact, handheld, and portable design.

Package Contents

Upon opening the package, please verify that all items are present and in good condition:

• 1 x TC CP-40S Laser Distance Meter
• 1 x Portable Pouch
• 1 x Hanging Rope
• 1 x User Manual (this document)

Image: The TC CP-40S Laser Distance Meter shown alongside its retail packaging and the included hanging rope, demonstrating the complete package contents.

Safety Instructions

This device uses a Class 2 laser. Please observe the following safety precautions:

• DO NOT stare directly into the laser beam.
• DO NOT point the laser beam at people or animals.
• Avoid direct eye exposure to the laser beam.
• Keep the device out of reach of children.
• Do not attempt to modify or disassemble the device. Unauthorized modifications can lead to hazardous laser radiation exposure.
• Use only the specified battery type (2 x 1.5V AAA).
• Do not operate the device in explosive environments or near flammable liquids or gases.
• Ensure the device is clean and dry before use.

Image: A side and back view of the laser distance meter, highlighting the yellow caution label with laser safety warnings and specifications.

Setup

Battery Installation

The TC CP-40S requires two 1.5V AAA batteries (not included) for operation.

1. Locate the battery compartment cover on the back of the device.
2. Slide the cover downwards to open the compartment.
3. Insert two AAA batteries, ensuring the correct polarity (+ and -) as indicated inside the compartment.
4. Close the battery compartment cover by sliding it upwards until it clicks into place.

Image: The back of the laser distance meter with the battery compartment cover removed, showing the two empty AAA battery slots and spring contacts.

Attaching the Hanging Rope

The included hanging rope can be attached to the device for convenient carrying and to prevent accidental drops.

1. Locate the small loop hole on the side or bottom of the device.
2. Thread the thin end of the hanging rope through the loop hole.
3. Pass the larger loop of the rope over the device and pull it tight to secure.

Operating Instructions

Device Overview and Buttons

Image: Front view of the TC CP-40S Laser Distance Meter, displaying its LCD screen, control buttons, and laser aperture.

Familiarize yourself with the device's buttons:

• ON/MEAS (Red Button): Powers on the device, initiates single measurement, or starts continuous measurement.
• + (Plus Button): Adds measurements, navigates up in menus.
• - (Minus Button): Subtracts measurements, navigates down in menus.
• UNIT Button: Changes measurement units (m, ft, in).
• Function Button (Cube Icon): Toggles between distance, area, volume, and Pythagorean measurement modes.
• Reference Point Button (Arrows Icon): Switches between front and rear measurement reference points.
• CLR/OFF (Red Button): Clears the current measurement, exits a function, or powers off the device (long press).

Powering On/Off

• To Power On: Press the ON/MEAS button. The backlight will illuminate, and the device will be ready for use.
• To Power Off: Press and hold the CLR/OFF button for a few seconds. The device also features an automatic power-off function after 150 seconds of inactivity to conserve battery life.

Changing Measurement Units

Press the UNIT button repeatedly to cycle through the available measurement units: meters (m), feet (ft), and inches (in).

Setting Measurement Reference Point

The device can measure from its front edge or its rear edge. Press the Reference Point button (arrows icon) to toggle between these two options. The display will show an icon indicating the current reference point.

Single Distance Measurement

1. Ensure the device is powered on.
2. Point the laser at the target surface.
3. Press the ON/MEAS button once. The laser will activate.
4. Press the ON/MEAS button again to take the measurement. The result will be displayed on the screen.

Area Measurement

1. Press the Function button (cube icon) until the area icon (rectangle) appears on the display.
2. Measure the first side (e.g., length) by pressing ON/MEAS.
3. Measure the second side (e.g., width) by pressing ON/MEAS again.
4. The device will automatically calculate and display the area.

Volume Measurement

1. Press the Function button (cube icon) until the volume icon (3D cube) appears on the display.
2. Measure the length by pressing ON/MEAS.
3. Measure the width by pressing ON/MEAS.
4. Measure the height by pressing ON/MEAS.
5. The device will automatically calculate and display the volume.

Pythagorean Measurement (Indirect Measurement)

This mode allows you to calculate inaccessible heights or distances using two or three measurements based on the Pythagorean theorem.

1. Press the Function button (cube icon) until the desired Pythagorean mode icon appears (e.g., triangle with one unknown side).
2. Follow the on-screen prompts to take the required measurements (e.g., hypotenuse, base).
3. The device will calculate and display the unknown side.

Addition and Subtraction of Measurements

After taking a measurement:

• Press the + button to add the next measurement to the current one.
• Press the - button to subtract the next measurement from the current one.
• Take the next measurement by pressing ON/MEAS. The result will be updated.

Min/Max Distance Tracking (Continuous Measurement)

1. Press and hold the ON/MEAS button. The device will enter continuous measurement mode.
2. Move the device slowly towards or away from the target. The display will show the current distance, along with the minimum and maximum distances recorded during the session.
3. Press CLR/OFF or ON/MEAS to exit continuous measurement.

Maintenance

• Cleaning: Use a soft, damp cloth to clean the device. Do not use abrasive cleaners or solvents. Ensure the laser lens is clean and free of dust for accurate measurements.
• Storage: When not in use for extended periods, remove the batteries to prevent leakage. Store the device in its portable pouch in a cool, dry place, away from direct sunlight and extreme temperatures.
• Battery Replacement: Replace batteries when the low battery indicator appears on the display. Always use new 1.5V AAA alkaline batteries.
• Avoid Drops: While the device is designed to be robust, avoid dropping it or subjecting it to strong impacts, which can affect its calibration and functionality.

Troubleshooting

Specifications

Warranty and Support

For warranty information or technical support, please refer to the contact details provided with your purchase or visit the official TC website. Keep your purchase receipt as proof of purchase for warranty claims.

This product is designed for general measurement purposes. For professional or critical applications, always cross-verify measurements with other calibrated instruments.