RUBI Tile Level Quick Set Leveling System Model 2941 Instruction Manual

1. Introduction and System Overview

The RUBI Tile Level Quick Set Leveling System, Model 2941, is designed to facilitate the precise installation of ceramic tiles, preventing lippage and ensuring a flat, uniform surface. This system is particularly effective for large-format tiles and is compatible with tile thicknesses ranging from 3 mm to 16 mm. It simplifies the tile laying process by maintaining consistent spacing and preventing movement during adhesive curing.

2. Product Components

The RUBI Tile Level Quick Set Leveling System Model 2941 includes the following components:

• Leveling Strips: Disposable components inserted between tiles to create a minimum 1.5 mm joint and hold tiles at an even height.
• Reusable Caps: These POM (Polyoxymethylene) caps are placed over the strips and tightened to apply pressure, ensuring tile flatness. Their robust design allows for multiple uses.
• Tile Leveling Pliers: An ergonomic tool designed to apply controlled and consistent pressure to the caps, adjusting based on tile thickness for optimal leveling.

Image: The complete set of RUBI Tile Level Quick components, including 100 reusable caps, 100 leveling strips, and one pair of leveling pliers.

3. Setup and Preparation

1. Surface Preparation: Ensure the substrate is clean, dry, and structurally sound. Any unevenness in the substrate should be addressed prior to tile installation.
2. Tile Compatibility: Verify that your tiles have a thickness between 3 mm and 16 mm.
3. Adhesive Application: Apply tile adhesive to the substrate using the appropriate trowel size. For large-format tiles, it is recommended to use a double-gluing technique, applying adhesive to both the substrate and the back of the tile (back-buttering), to ensure maximum coverage and adhesion.

4. Operating Instructions

Follow these steps for effective use of the RUBI Tile Level Quick Set Leveling System:

1. Place Leveling Strips: After applying adhesive and placing the first tile, insert the base of the leveling strips underneath the tile, ensuring the strip's stem protrudes into the joint. Place strips at each corner of the tile and along the edges as needed for larger tiles (typically 2-4 strips per side).
2. Position Next Tile: Carefully place the adjacent tile, ensuring it makes full contact with the adhesive and the leveling strips are correctly positioned between the tiles.
3. Install Reusable Caps: Thread a reusable cap onto the stem of each leveling strip. Hand-tighten the cap until it makes contact with the tile surface.
4. Tighten with Pliers: Use the RUBI Tile Leveling Pliers to apply final pressure. Adjust the pliers according to the tile thickness to ensure the correct and necessary pressure is applied. Squeeze the pliers to tighten the cap, bringing the tile edges into perfect alignment and eliminating lippage.

Image: Demonstrating the use of the RUBI Tile Leveling Pliers to tighten a cap, leveling adjacent tiles.

5. Allow Adhesive to Cure: Allow the tile adhesive to fully cure according to the manufacturer's instructions before proceeding to the next step. Do not remove the leveling system prematurely.
6. Remove System: Once the adhesive is completely dry, remove the leveling system by striking the caps with a rubber mallet or kicking them along the joint line. The strips are designed to break off cleanly at the base, leaving the cap free for reuse. Always strike in the direction of the joint.

5. Maintenance

The reusable caps of the RUBI Tile Level Quick system are made from durable POM material. After each use, clean any residual adhesive from the caps to ensure their longevity and proper function for future projects. Store all components in a clean, dry place.

6. Troubleshooting

If you encounter issues during installation, consider the following:

• Lippage persists: Ensure sufficient adhesive coverage and proper strip placement. Verify that the caps are tightened adequately with the pliers, adjusting the pliers for the correct tile thickness.
• Strips breaking prematurely: This may indicate excessive force during tightening or incorrect pliers adjustment. Ensure the pliers are set to the appropriate tile thickness and apply gradual, firm pressure.
• Difficulty removing strips: Ensure the adhesive is fully cured. Striking the caps along the joint line with a rubber mallet should cleanly break the strips.

7. Specifications

8. Warranty and Support

For warranty information, technical support, or inquiries regarding replacement parts, please contact RUBI customer service directly. Refer to the product packaging or the official RUBI website for contact details.