EKYLIN 7-Inch TFT LCD Car Rearview Monitor Instruction Manual

Introduction

The EKYLIN 7-inch TFT LCD Car Rearview Monitor (Model 7001B) is designed to enhance vehicle safety and convenience. It supports up to two video inputs and displays high-resolution images, making it suitable for rearview cameras, parking systems, and other video devices. This monitor features adjustable brightness, contrast, and color settings, and is compatible with 12V-24V vehicles.

Package Contents

Upon opening the package, verify that all components are present:

• 7-inch TFT LCD Monitor
• IR Remote Control
• Power Cable (12V/24V cigarette lighter adapter)
• Video Cable (RCA)
• Adjustable Mounting Bracket (Suction Cup)
• Adhesive Mounting Pad
• Installation Guide

Figure 1: Overview of the EKYLIN 7-inch monitor and its included accessories.

Setup

1. Mounting the Monitor

The monitor offers two primary mounting options: a suction cup mount for windshields or a dashboard mount using an adhesive pad.

1. Attach the Monitor to the Bracket: Securely attach the monitor to your preferred mounting bracket (suction cup or adhesive pad mount). Ensure the monitor is firmly seated.
2. Position the Monitor: Choose a location on your dashboard or windshield that provides optimal visibility without obstructing your view of the road. Clean the surface thoroughly before applying the suction cup or adhesive pad.
3. Secure the Mount: For the suction cup mount, press firmly against the surface and engage the locking lever. For the adhesive pad mount, peel off the protective film and press the pad firmly onto the dashboard.

Figure 2: The monitor installed on a vehicle dashboard, demonstrating a typical viewing angle.

2. Connecting the Camera and Power

The monitor supports two video inputs (AV1 and AV2) and is powered via a 12V/24V accessory port.

1. Connect the Camera: Connect your rearview camera's RCA video output cable to either the AV1 or AV2 input on the monitor. AV2 is typically used for backup cameras as it supports automatic switching when reverse gear is engaged.
2. Power the Camera: Ensure your camera is properly powered according to its own instructions.
3. Connect Monitor Power: Plug the monitor's power cable (cigarette lighter adapter) into your vehicle's 12V/24V accessory port.
4. Route Cables: Carefully route all cables to avoid interference with driving controls and to maintain a tidy appearance. Utilize existing trim or weather stripping to conceal cables where possible.

Figure 3: The monitor with its sunshade, designed to reduce glare and improve visibility.

Figure 4: The back of the monitor, showing the heat radiation holes for optimal performance.

Operating Instructions

1. Power On/Off

Press the power button on the monitor or the remote control to turn the unit on or off. The monitor will automatically power on when a video signal is detected on AV2 (typically when reverse gear is engaged).

2. Video Input Selection

Use the 'V1/V2' button on the monitor or the 'VIDEO SELECT' button on the remote control to switch between AV1 and AV2 video inputs.

3. Adjusting Display Settings

The monitor's display settings can be adjusted using the buttons on the front panel or the IR remote control.

• Menu: Press the 'MENU' button to access the display settings.
• Navigation: Use the arrow buttons (up/down/left/right) on the remote or the corresponding buttons on the monitor to navigate through options and adjust values.
• Settings: Adjust Brightness, Contrast, Color, and Aspect Ratio (16:9 or 4:3) to your preference.

4. Backup Camera Functionality

When connected to a backup camera via AV2 and properly wired to your vehicle's reverse lights, the monitor will automatically display the camera feed when the vehicle is put into reverse. The display includes parking guide lines (red, yellow, green) to assist with parking maneuvers.

Maintenance

• Cleaning: Use a soft, dry cloth to clean the monitor screen and casing. Avoid abrasive cleaners or solvents.
• Cable Inspection: Periodically check all cables for signs of wear, damage, or loose connections.
• Mount Security: Ensure the mounting bracket remains securely attached to prevent the monitor from falling during vehicle operation.

Troubleshooting

• No Power: Ensure the power cable is securely plugged into the vehicle's accessory port and the monitor. Check the vehicle's fuse for the accessory port.
• No Video Signal: Verify that the camera is powered on and its video cable is correctly connected to the monitor's AV input. Ensure the correct AV input (AV1/AV2) is selected.
• Poor Image Quality: Check camera lens for dirt or obstructions. Adjust monitor brightness, contrast, and color settings. Ensure the video cable is not damaged.
• Monitor Not Switching Automatically: Confirm the backup camera is connected to AV2 and the trigger wire (if applicable) is correctly connected to the reverse light circuit.

Specifications

Warranty and Support

EKYLIN offers a Free Lifetime Warranty for this product. For technical assistance, troubleshooting, or warranty claims, please refer to the contact information provided in your product packaging or visit the official EKYLIN support website.