Cata B&Q Designair Cooke & Lewis Cooker Hood Control Button PCB Instruction Manual

Introduction

This manual provides essential information for the safe and correct installation, operation, and maintenance of your Cata B&Q Designair Cooke & Lewis Cooker Hood Control Button PCB. This component is an original replacement part designed to restore the functionality of your cooker hood's control panel. Please read these instructions thoroughly before proceeding with installation or use.

Safety Information

Improper installation or repair can lead to electrical shock, fire, or other hazards. Always adhere to the following safety guidelines:

• Disconnect Power: Before attempting any installation, maintenance, or repair, ensure the cooker hood is completely disconnected from the main power supply. Turn off the circuit breaker or remove the fuse.
• Professional Installation Recommended: Installation of electrical components should ideally be performed by a qualified electrician or a competent person with experience in appliance repair.
• Handle with Care: The PCB contains sensitive electronic components. Avoid touching the circuit board directly with bare hands to prevent electrostatic discharge damage.
• Use Correct Tools: Ensure you have the appropriate tools for the task, including insulated screwdrivers.
• Verify Compatibility: Confirm that this replacement PCB is compatible with your specific cooker hood model before installation.

Package Contents

Verify that all components are present and undamaged upon receipt:

• 1x Cata B&Q Designair Cooke & Lewis Cooker Hood Control Button PCB (Model 15100031)
• Mounting hardware (if applicable, as specified by the manufacturer)

Compatible Models

This control button PCB is compatible with the following cooker hood models:

• CHP60SS
• CHP70SS
• CHP90SS
• CLCH60SS-C
• CLCH90SS-C
• CLGCH60-C
• CLGCH90-C
• CTCG60
• FGHD62SS
• FGHD72SS

Always cross-reference the model number of your appliance to ensure correct part selection.

Setup and Installation

Follow these steps carefully to replace the control button PCB. If you are unsure at any point, consult a qualified technician.

1. Prepare for Installation:
   • Ensure the cooker hood is completely disconnected from the main power supply.
   • Gather necessary tools: screwdrivers (Phillips and flathead), possibly pliers, and a camera to document wiring.
2. Access the Existing PCB:
   • Depending on your cooker hood model, you may need to remove filters, light covers, or decorative panels to access the control panel assembly. Refer to your cooker hood's specific service manual for detailed access instructions.
   • Carefully locate the existing control button PCB.
3. Document Wiring:
   • Before disconnecting any wires, take clear photographs of all wire connections to the old PCB. Note the color and position of each wire. This is crucial for correct reassembly.
4. Disconnect the Old PCB:
   • Carefully disconnect all wires from the old PCB. Note if any connectors are unique or keyed.
   • Unscrew or unclip the old PCB from its mounting points.
5. Install the New PCB:
   • Position the new control button PCB (Model 15100031) in the same location as the old one.
   • Secure the new PCB using the original screws or clips. Ensure it is firmly seated.
   

   Image 1: The Cata B&Q Designair Cooke & Lewis Cooker Hood Control Button PCB (Model 15100031) with its integrated wiring harness. This image shows the main body of the PCB and the multi-colored wires extending from it, ready for connection.

6. Reconnect Wiring:
   • Using your photographs and notes, carefully reconnect all wires to the new PCB. Ensure each wire is connected to its correct terminal. Double-check all connections for security.
   

   Image 2: Top view of the control button assembly, showing the five metallic buttons and the main housing. This perspective highlights the user interface aspect of the PCB.

   

   Image 3: Angled view of the control button assembly, providing a clearer look at the side profile and the connection points for the wiring harness. This view helps in understanding how the buttons integrate with the PCB.

7. Reassemble the Cooker Hood:
   • Once all connections are secure, reattach any panels, light covers, or filters that were removed.
8. Restore Power and Test:
   • Restore power to the cooker hood at the main circuit breaker.
   • Test all functions of the control panel (fan speeds, lights, etc.) to ensure the new PCB is working correctly.

Operating Instructions

This PCB controls the various functions of your cooker hood via its integrated buttons. Once installed, the operation should be intuitive and consistent with your cooker hood's original design.

• Power On/Off: Typically, one button controls the main power to the fan and lights.
• Fan Speed Selection: Multiple buttons or a single button with sequential presses will adjust the fan speed (e.g., Low, Medium, High).
• Light Control: A dedicated button usually controls the cooker hood's lighting.

Refer to your cooker hood's primary user manual for specific button functions and operational sequences.

Maintenance

The control button PCB itself requires minimal maintenance. However, proper care of the surrounding control panel can extend its lifespan.

• Cleaning the Control Panel: Ensure the cooker hood is powered off before cleaning. Use a soft, damp cloth with a mild, non-abrasive cleaner to wipe the surface of the control panel. Avoid spraying liquids directly onto the buttons or gaps.
• Avoid Excessive Force: Do not press the buttons with excessive force, as this can damage the internal mechanisms or the PCB.

Troubleshooting

If you encounter issues after installing the new PCB, consider the following common troubleshooting steps:

If troubleshooting steps do not resolve the issue, it is recommended to contact a qualified service technician.

Specifications

Warranty and Support

For information regarding warranty coverage, returns, or technical support, please refer to the original purchase documentation or contact the retailer or manufacturer directly. Keep your proof of purchase for any warranty claims.