3M DBI-SALA Pullaway Wristband Instruction Manual

1. Introduction

This manual provides essential information for the proper use, setup, and maintenance of the 3M DBI-SALA Pullaway Wristband. This product is designed to help prevent dropped tools in industrial and occupational environments. It features a slim profile and elastic construction for user comfort and tool security. Please read this manual thoroughly before using the product.

Image 1.1: The 3M DBI-SALA Pullaway Wristband, a slim profile elastic wristband with a D-ring connection point.

2. Important Safety Information

WARNING: For industrial/occupational use only. Not for consumer sale or use. 3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace use. Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. OSHA, ANSI), as well as all product literature, user instructions, warnings, and limitations. Misuse of 3M industrial and occupational products may result in injury, sickness, or death. For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert.

Always inspect the wristband for damage before each use. Do not use if any signs of wear, cuts, or damage are present. Ensure the D-ring is securely attached and free from deformation.

3. Setup and Installation

The 3M DBI-SALA Pullaway Wristband is designed for easy and secure attachment to the user's wrist.

1. Select Correct Size: Ensure you are using the appropriate size wristband (Small in this case) for a snug yet comfortable fit. The elastic material is designed to conform to the user's wrist.
2. Wear on Wrist: Slide the wristband onto your wrist. It should fit securely without being overly tight or loose, allowing for full range of motion without slipping.
3. Position D-Ring: Position the D-ring in a convenient location on your wrist, typically on the top or side, to allow for easy attachment of tools.

Image 3.1: Close-up view of the D-ring connection point on the wristband, showing the robust yellow webbing.

4. Operating Instructions

Once the wristband is securely in place, it can be used to tether small hand tools.

1. Attach Tool Tether: Connect a compatible tool tether (sold separately) to the D-ring on the wristband. Ensure the tether's connector is fully closed and locked.
2. Secure Tool: Attach the other end of the tool tether to the small hand tool you intend to use. Verify that the tool is securely fastened to the tether.
3. Weight Capacity: Do not exceed the maximum weight capacity of 5 lb (2.3 kg) for the wristband. Overloading can compromise safety and product integrity.
4. Movement: Ensure the tethered tool allows for necessary movement and operation without creating snagging hazards.

Image 4.1: A worker demonstrating the use of the wristband with a tethered wrench, illustrating how tools can be secured to prevent drops.

5. Maintenance

Proper maintenance ensures the longevity and continued safety of your Pullaway Wristband.

• Regular Inspection: Before each use, visually inspect the wristband for any signs of wear, fraying, cuts, tears, or damage to the elastic material or the D-ring.
• Cleaning: If the wristband becomes dirty, clean it with mild soap and water. Rinse thoroughly and allow it to air dry completely before storage or next use. Do not use harsh chemicals or abrasive cleaners.
• Storage: Store the wristband in a cool, dry place away from direct sunlight, extreme temperatures, and corrosive substances.
• Disposal: If the wristband shows any signs of damage or excessive wear, it must be immediately removed from service and properly disposed of to prevent accidental reuse.

6. Troubleshooting

The 3M DBI-SALA Pullaway Wristband is a simple device, and most issues relate to inspection and proper use.

• Wristband feels too loose or too tight: Ensure you have selected the correct size. While elastic, an improperly sized wristband may not provide optimal comfort or security.
• D-ring appears bent or damaged: Immediately discontinue use. A damaged D-ring compromises the integrity of the tool tethering system.
• Elastic material is frayed or cut: Discontinue use. Any damage to the material can lead to failure.
• Tool detaches from tether: Re-evaluate the connection points of your tool tether. Ensure all connectors are properly engaged and secured to both the wristband's D-ring and the tool. Verify the tool's weight does not exceed the wristband's capacity.

If you encounter any issues not covered here or have concerns about the product's performance, contact 3M customer support.

7. Specifications

8. Warranty and Support

For information regarding product warranty, technical support, or any other inquiries, please contact 3M directly. Refer to the official 3M website or product packaging for the most current contact details and warranty policies.

Manufacturer: 3M

Website: www.3m.com