1. Introduction
This manual provides essential information for the proper installation, maintenance, and safe use of your CUB CADET 720-04049A Handle Grip. Please read this manual thoroughly before attempting any installation or maintenance procedures to ensure correct application and longevity of the part.
2. Safety Information
Always prioritize safety when working with machinery and replacement parts. Failure to follow safety instructions may result in injury or damage.
- Wear appropriate personal protective equipment (PPE), such as gloves and eye protection.
- Ensure the equipment is turned off and disconnected from any power source before beginning installation or maintenance.
- Refer to your equipment's original owner's manual for specific safety precautions related to your model.
- Keep children and bystanders away from the work area.
- Use only genuine CUB CADET replacement parts to ensure proper fit and function.
3. Product Overview
The CUB CADET 720-04049A Handle Grip is an OEM replacement part designed to provide a secure and comfortable grip on compatible CUB CADET equipment. It replaces prior MPN 720-04049.
Figure 1: CUB CADET 720-04049A Handle Grip (Front View)
4. Compatibility
This handle grip is compatible with the following CUB CADET models:
- CC30 Mini Rider
- CC30H Hydro Mini Rider
- CC30-H Hydro Mini Rider
- CC30-H Mini Rider
- 19A40024 2-Inch 3x Snow Thrower
- 42-Inch 3x Snow Thrower
Always refer to your original equipment owner's manual to verify compatibility before purchasing and installing any replacement parts.
5. Installation
Follow these general steps for installing the handle grip. Specific procedures may vary based on your equipment model.
- Prepare the Equipment: Ensure the equipment is powered off and any moving parts have come to a complete stop. Disconnect the spark plug wire or battery if applicable to prevent accidental starting.
- Remove Old Grip (if applicable): Carefully remove the existing handle grip. This may involve cutting it off, prying it loose, or unscrewing retaining components. Note how the old grip was attached.
- Clean Handle Bar: Clean the handle bar surface where the new grip will be installed. Remove any residue, dirt, or rust to ensure a smooth and secure fit.
- Install New Grip: Slide the new CUB CADET 720-04049A Handle Grip onto the handle bar. Apply firm, even pressure. If necessary, a small amount of rubbing alcohol or grip adhesive (not included) can be used to aid installation and secure the grip, allowing it to dry completely before use.
- Verify Secure Fit: Once installed, ensure the grip is firmly seated and does not rotate or slide freely.
- Reconnect Power: Reconnect the spark plug wire or battery.
Figure 2: CUB CADET 720-04049A Handle Grip (Side View)
6. Operating
The handle grip functions as a direct interface for controlling your equipment. Ensure a firm and comfortable hold during operation. If the grip feels loose or damaged, replace it immediately to maintain safe control of the machinery.
7. Maintenance
Regular maintenance helps prolong the life of your handle grip and ensures safe operation.
- Cleaning: Wipe the handle grip with a damp cloth to remove dirt and debris. Avoid harsh chemicals that may degrade the plastic material.
- Inspection: Periodically inspect the grip for signs of wear, cracks, tears, or looseness. A worn or damaged grip can compromise control and safety.
- Replacement: Replace the handle grip if it shows significant signs of wear or damage, or if it becomes loose on the handle bar.
8. Troubleshooting
Refer to the table below for common issues and their potential solutions.
| Issue | Possible Cause | Solution |
|---|---|---|
| Grip feels loose after installation | Improper installation; incorrect size; no adhesive used. | Re-install, ensuring firm pressure. Consider using a small amount of grip adhesive. Verify part compatibility. |
| Grip is difficult to install | Handle bar not clean; grip not aligned; incorrect size. | Clean handle bar thoroughly. Ensure proper alignment. Verify part compatibility. A small amount of rubbing alcohol can aid sliding. |
| Grip shows premature wear | Heavy use; exposure to harsh elements; improper cleaning agents. | Replace grip. Store equipment in a protected area. Use mild cleaning agents. |
9. Specifications
| Specification | Detail |
|---|---|
| Part Number | 720-04049A |
| Replaces MPN | 720-04049 |
| Brand | CUB CADET |
| Material | Plastic |
| Item Weight | 0.13 Pounds (approx. 59 grams) |
| Item Dimensions (LxWxH) | 3.75 x 1.5 x 1.25 inches |
| UPC | 195997294430 |
10. Warranty Information
This CUB CADET handle grip comes with a 3-month warranty. For specific terms and conditions, please refer to the warranty documentation provided with your original equipment or contact CUB CADET customer support.
11. Customer Support
For further assistance, technical support, or to inquire about other genuine CUB CADET parts, please visit the official CUB CADET website or contact their customer service department. Always have your equipment model number and the part number (720-04049A) ready when contacting support.
You can find more information and products at the CUB CADET Store on Amazon.
