1. Product Overview
This document provides essential information for the CUB CADET 732-1014C Torsion Spring. This genuine OEM part is designed for specific Cub Cadet equipment, ensuring proper fit and function. It replaces prior MPN 732-1014.
Figure 1: CUB CADET 732-1014C Torsion Spring, main view. This image shows the coiled body of the spring with its two extended arms.
2. Compatibility
The CUB CADET 732-1014C Torsion Spring is compatible with various Cub Cadet models. Always refer to your original equipment owner's manual to verify compatibility before installation.
Known Compatible Models:
- Cub Cadet: CC189, CC439, CC469, CC46ES, CC46M, CC46MZ, CC500, CC500BAT, CC500EL, CC550ES, CC550SP, CC550SPES
- Walk Behind Mowers: SC100, SC100H, SC100HW, SC300, SC300B, SC300E, SC300HW, SC300IP, SC300K, SC500, SC500E, SC500EQ, SC500EZ, SC500HW, SC500K, SC500Z, SC700, SC700H, SCP100, SCP21E
3. Specifications
| Attribute | Value |
|---|---|
| Part Number | 732-1014C |
| Manufacturer | CUB CADET |
| Product Dimensions | 2 x 1.25 x 1.25 inches |
| Item Weight | 0.8 ounces |
4. Setup and Installation
This torsion spring is a replacement part. Installation typically involves removing the old spring and fitting the new one into its designated position on the equipment. Due to the variety of compatible models, specific installation steps will vary.
General Guidelines:
- Safety First: Always ensure the equipment is turned off, disconnected from power (if electric), and any moving parts are secured before beginning work. Wear appropriate personal protective equipment (PPE), such as gloves and eye protection.
- Consult Manual: Refer to the specific owner's manual for your Cub Cadet equipment model for detailed, step-by-step instructions on replacing the torsion spring. This will provide diagrams and precise torque specifications if applicable.
- Tools: Gather any necessary tools as specified in your equipment's manual. This may include wrenches, pliers, or screwdrivers.
- Removal: Carefully remove the old torsion spring. Note its orientation and how it was attached to ensure correct installation of the new part.
- Installation: Position the new 732-1014C Torsion Spring according to your equipment's manual. Ensure it is securely fastened and functions correctly before operating the equipment.
Figure 2: Angled view of the torsion spring, showing the coil and the two arms extending in different directions, crucial for correct placement during installation.
5. Maintenance
Torsion springs are generally low-maintenance components. However, periodic inspection can extend their lifespan and ensure optimal performance of your equipment.
Maintenance Tips:
- Visual Inspection: Regularly check the spring for signs of wear, corrosion, cracks, or deformation. A damaged spring should be replaced immediately.
- Cleanliness: Keep the area around the spring free from dirt, debris, and grass clippings, which can impede its function or cause premature wear.
- Lubrication: Consult your equipment's owner's manual to determine if lubrication is recommended for the spring or its pivot points. If so, use the specified lubricant.
Figure 3: Close-up view of one end of the torsion spring, highlighting the bend and finish of the metal. This area should be inspected for signs of stress or damage.
6. Troubleshooting
If your equipment is not functioning as expected and you suspect the torsion spring is the cause, consider the following:
- Loss of Tension: If the mechanism the spring supports feels loose or does not return to its original position, the spring may have lost its tension or be broken.
- Visible Damage: Inspect the spring for any visible breaks, bends, or severe corrosion. A broken spring will require replacement.
- Incorrect Installation: Ensure the spring is installed correctly and securely. An improperly seated spring may not function effectively.
If troubleshooting does not resolve the issue, consult a qualified service technician or refer to your equipment's comprehensive service manual.
Figure 4: Close-up view of the second end of the torsion spring, showing its distinct angle. Both ends must be correctly engaged for the spring to function.
7. Warranty and Support
For information regarding the warranty of your CUB CADET 732-1014C Torsion Spring, please refer to the warranty documentation provided with your original Cub Cadet equipment or contact Cub Cadet customer support directly. As an OEM part, its warranty coverage is typically tied to the equipment it is installed in.
For further assistance or to locate authorized service centers, visit the official Cub Cadet website or consult your equipment's owner's manual for contact information.
Note: This manual provides general guidance. Always prioritize the specific instructions and safety warnings found in your equipment's owner's manual.
