Rust-Oleum 271198

Download PDF
Contents

Zinsser Bondz Maximum Adhesion Primer User Manual

Model: 271198

1. Introduction

Thank you for choosing Zinsser Bondz Maximum Adhesion Primer. This water-based, urethane-modified acrylic bonding primer is engineered for superior adhesion to challenging surfaces, preparing them for a wide range of topcoats. This manual provides essential information for safe and effective use, including setup, application, maintenance, and troubleshooting.

2. Safety Information

Always prioritize safety when working with paints and primers. Read and understand all instructions before use.

  • Ventilation: Use in a well-ventilated area. Ensure adequate fresh air during application and drying.
  • Personal Protective Equipment: Wear appropriate personal protective equipment (PPE), including safety glasses to protect eyes and gloves to protect skin.
  • Inhalation: Avoid breathing vapors or spray mist. If ventilation is poor, use a respirator approved for organic vapors.
  • Skin Contact: Avoid contact with skin. Wash thoroughly with soap and water after handling.
  • Eye Contact: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention.
  • Ingestion: Do not ingest. If swallowed, call a poison control center or doctor immediately. Do not induce vomiting.
  • Flammability: Keep away from heat, sparks, and open flame.
  • Storage: Store in a cool, dry place, away from direct sunlight and freezing temperatures. Keep container tightly closed when not in use.
  • Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
  • Children and Pets: Keep out of reach of children and pets.

3. Product Overview

Zinsser Bondz Maximum Adhesion Primer is designed to provide excellent adhesion on a variety of challenging surfaces, both interior and exterior. Its low VOC and low odor formula makes it suitable for use in occupied spaces.

  • Bonds all topcoats to hard, dense surfaces.
  • Compatible with all paints, including solvent-based and two-part epoxies.
  • Fast curing, allowing topcoat application in 1 hour.
  • Low odor and low VOC (Volatile Organic Compounds).
  • Suitable for multi-surface applications.
Four Zinsser Bondz Maximum Adhesion Primer quart cans

Image: Four quart cans of Zinsser Bondz Maximum Adhesion Primer, showcasing the product packaging and branding. Each can is labeled with 'BONDZ Maximum Adhesion Primer' and 'Item No 271198'.

4. Setup and Surface Preparation

Proper surface preparation is crucial for optimal adhesion and finish.

  1. Clean Surface: Ensure the surface is clean, dry, and free of dust, dirt, grease, wax, and loose paint. Use a suitable cleaner if necessary, and rinse thoroughly.
  2. Remove Loose Material: Scrape off any loose or peeling paint. Sand glossy surfaces to dull the finish and improve adhesion.
  3. Repair Imperfections: Fill any cracks or holes with appropriate patching compound and allow to dry. Sand smooth.
  4. Masking: Mask off any areas not intended for priming, such as trim, windows, or adjacent walls, using painter's tape.
  5. Stir Thoroughly: Before use, stir the primer thoroughly to ensure all components are well mixed. Do not thin.

5. Application Guidelines

Apply Zinsser Bondz Maximum Adhesion Primer using a high-quality synthetic brush, roller, or airless sprayer.

  1. Application Temperature: Apply when air and surface temperatures are between 50°F (10°C) and 90°F (32°C).
  2. Application Method:
    • Brush: Use a good quality synthetic brush.
    • Roller: Use a 3/8" nap roller cover for smooth to semi-smooth surfaces.
    • Airless Sprayer: Use a .015"-.017" tip at 2000-2500 PSI.
  3. Coverage: This primer covers approximately 400 sq-ft per gallon, depending on surface porosity.
  4. Drying Time: Dries to touch in 30 minutes. Recoat or topcoat in 1 hour. For two-part epoxies, allow 6 hours before topcoating.
  5. Number of Coats: One coat is typically sufficient. For extremely porous or stained surfaces, a second coat may be applied after 1 hour.

6. Care and Storage

Proper care and storage will extend the life of your product and tools.

  • Cleaning Tools: Clean brushes, rollers, and spray equipment immediately after use with warm soapy water.
  • Spills: Clean up spills immediately with a damp cloth.
  • Storage: Store unused primer in its original container, tightly sealed, in a cool, dry place away from direct sunlight and freezing temperatures. Do not allow to freeze.
  • Disposal: Dispose of unused product and empty containers according to local regulations. Do not pour down drains.

7. Troubleshooting

Refer to the table below for common issues and their solutions.

ProblemPossible CauseSolution
Poor AdhesionImproper surface preparation (dirty, greasy, glossy surface)Ensure surface is clean, dry, and dull. Sand glossy surfaces.
Uneven FinishInconsistent application, improper roller nap, or surface imperfections.Apply evenly. Use appropriate roller nap for surface. Repair surface imperfections before priming.
Slow Drying TimeHigh humidity, low temperature, or excessive film thickness.Ensure adequate ventilation. Apply within recommended temperature range. Apply thin, even coats.
Bubbling/FoamingOver-rolling, applying too quickly, or surface contamination.Avoid over-rolling. Apply at a steady pace. Ensure surface is clean.

8. Specifications

Key technical details for Zinsser Bondz Maximum Adhesion Primer.

AttributeDetail
BrandRust-Oleum (Zinsser)
Model NameZinsser Bondz
Item Model Number271198
ColorWhite (Tintable)
Finish TypeGloss
Item Volume32 Fluid Ounces (per can)
Unit Count128.0 Fluid Ounces (4-pack)
Paint TypeWatercolor (Water-based)
Specific UsesInterior/Exterior
Surface RecommendationMulti Surface
Special FeatureLow Odor
Full Cure Time1 Hour (for topcoat)
Coverage400 sq-ft/gal
Country of OriginUSA

9. Warranty and Support

Rust-Oleum stands behind the quality of its products. For specific warranty details or technical support, please refer to the product packaging or visit the official Rust-Oleum website. If you have questions regarding product application, performance, or safety, please contact Rust-Oleum customer service.

Contact Information:
Please refer to the contact details provided on the product label or the official Rust-Oleum website for the most current support information.

© 2024 Rust-Oleum. All rights reserved. Information subject to change without notice.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.