Hublot Classic Fusion Automatic Watch

Introduction

Congratulations on your purchase of the Hublot Classic Fusion Automatic Watch, model 511.NX.1171.LR. This timepiece combines sophisticated design with precision automatic movement, offering reliable timekeeping and a timeless aesthetic. This manual provides essential information for the proper setup, operation, maintenance, and care of your watch to ensure its longevity and optimal performance.

Setup

1. Unboxing and Initial Inspection

Carefully remove your watch from its packaging. Inspect the watch for any protective films on the crystal, case back, or bracelet/strap. Remove these films gently before wearing. Ensure all components, such as the watch, warranty card, and instruction booklet, are present.

Front view of the Hublot Classic Fusion Automatic Watch, showcasing the black dial and brushed titanium case.

2. Winding the Watch

Your Hublot Classic Fusion is equipped with an automatic mechanical movement. While it winds itself with the motion of your wrist, it may require manual winding if it has stopped or has not been worn for an extended period. To manually wind:

1. Gently unscrew the crown (if it's a screw-down crown) and pull it out to position 1 (winding position).
2. Turn the crown clockwise approximately 30-40 times. This will build up a sufficient power reserve to start the watch.
3. Push the crown back in and screw it down securely (if applicable) to ensure water resistance.

3. Setting the Time and Date

To set the time and date on your watch:

1. Gently unscrew the crown (if applicable) and pull it out to position 2 (date setting position).
2. Turn the crown clockwise or counter-clockwise to adjust the date. Avoid setting the date between 9 PM and 3 AM, as this can damage the movement.
3. Pull the crown out to position 3 (time setting position). The seconds hand will stop.
4. Turn the crown to set the hour and minute hands. To ensure correct AM/PM, advance the hands past 12 o'clock; if the date changes, it is midnight.
5. Once the time is set, push the crown back into position 0 (normal operating position) and screw it down securely (if applicable). The seconds hand will resume movement.

Side view of the watch, showing the crown for winding and setting.

4. Adjusting the Strap/Clasp

The watch features a foldover clasp with a push button. To adjust the fit, ensure the strap is correctly sized for your wrist. If adjustments are needed, it is recommended to visit an authorized Hublot retailer or a professional watchmaker to avoid damaging the strap or clasp.

Operating Your Watch

1. Timekeeping

Once set, your automatic watch will keep accurate time as long as it is worn regularly or kept on a watch winder. The movement of your wrist powers the watch, maintaining its power reserve.

2. Date Function

The date display will automatically advance at midnight. If the watch has stopped and restarted, or if the month has fewer than 31 days, you may need to manually adjust the date as described in the 'Setting the Time and Date' section.

3. Power Reserve

The Hublot Classic Fusion Automatic has a power reserve that allows it to run for a certain period (typically 42-48 hours) when fully wound and not worn. If the watch stops, simply wind it manually or wear it to restart the movement.

Maintenance

1. Cleaning Your Watch

To maintain the appearance of your watch, clean the case and crystal regularly with a soft, damp cloth. For the leather strap, avoid excessive moisture and harsh chemicals. For deeper cleaning, especially for the case and clasp, a soft brush with mild soap and water can be used, ensuring the crown is securely screwed down.

2. Water Resistance

Your watch has a specific water resistance rating. Always ensure the crown is fully pushed in and screwed down (if applicable) before exposing the watch to water. Water resistance is not a permanent condition and may decrease over time due to wear and tear on gaskets. Avoid exposing the watch to hot water, steam, or sudden temperature changes, as this can compromise seals.

3. Servicing

Like any precision instrument, your Hublot watch requires periodic servicing to ensure its accuracy and longevity. It is recommended to have your watch serviced by an authorized Hublot service center every 3-5 years. This service typically includes cleaning, lubrication, and adjustment of the movement, as well as replacement of worn gaskets.

4. Storage

When not wearing your watch, store it in a cool, dry place, away from direct sunlight, extreme temperatures, and strong magnetic fields. The original watch box is ideal for storage.

Troubleshooting

• Watch not running: Ensure the watch is sufficiently wound. If it has stopped, manually wind it as described in the 'Setup' section. If the issue persists, it may require professional servicing.
• Date not changing: Check if the time is set correctly (AM/PM). Avoid setting the date between 9 PM and 3 AM. If the date mechanism is stuck, do not force it; seek professional assistance.
• Condensation under crystal: This indicates a breach in water resistance. Immediately take the watch to an authorized service center to prevent further damage to the movement.
• Inaccurate timekeeping: Minor variations are normal for mechanical watches. However, if the watch is consistently running too fast or too slow, it may need regulation by a professional watchmaker.

Specifications

Warranty and Support

Your Hublot Classic Fusion watch comes with a manufacturer's warranty covering defects in materials and workmanship. Please refer to the warranty card included with your purchase for specific terms, conditions, and duration. Keep your proof of purchase in a safe place.

For warranty claims, servicing, or technical support, please contact an authorized Hublot service center or the retailer from whom you purchased the watch. Using unauthorized service providers may void your warranty.

For more information, visit the official Hublot website or consult your local authorized dealer.