1. Introduction
This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your Einhell TC-TS 2025/1 U Table Saw. Please read this manual thoroughly before operating the machine to ensure proper use and to prevent injury or damage.
The Einhell TC-TS 2025/1 U is a powerful table saw designed for precise cutting of wood and similar materials. It features a 2000W motor and a 250mm saw blade, offering a maximum cutting height of 85mm.
2. Safety Instructions
WARNING: Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury.
- Always wear appropriate personal protective equipment (PPE) such as safety glasses, hearing protection, and a dust mask.
- Ensure the work area is clean, well-lit, and free from obstructions.
- Keep children and bystanders away from the operating area.
- Do not operate the saw in damp or wet conditions.
- Always disconnect the power supply before making adjustments, changing accessories, or performing maintenance.
- Use the push stick provided when cutting small workpieces.
- Ensure the saw blade is sharp and correctly installed.
- Never reach into the blade area while the saw is running.
3. Product Components
Familiarize yourself with the main parts of your Einhell TC-TS 2025/1 U Table Saw.
- Saw Table
- Saw Blade
- Blade Guard
- Parallel Stop
- Angle Stop
- Height/Angle Adjustment Handwheel
- On/Off Switch
- Dust Extraction Port
- Push Stick
- Stand
4. Setup and Assembly
Follow these steps to assemble and set up your table saw for initial use.
4.1 Assembling the Stand
Carefully unpack all components. Assemble the stand according to the diagrams provided in the separate assembly instructions. Ensure all bolts are securely tightened.
4.2 Installing the Saw Blade
- Ensure the saw is unplugged from the power supply.
- Remove the blade guard if necessary.
- Use the provided wrenches to loosen the blade nut.
- Carefully place the new blade onto the arbor, ensuring the teeth are pointing in the correct direction (usually indicated by an arrow on the blade and saw).
- Tighten the blade nut securely with the wrenches.
- Reinstall the blade guard.
4.3 Connecting Dust Extraction
Connect a suitable dust extraction system to the dust port on the saw to maintain a clean work environment and improve visibility.
5. Operating Instructions
5.1 Adjusting Blade Height and Angle
The blade height and angle can be adjusted using the handwheel located on the front of the saw.
- To adjust blade height: Turn the handwheel to raise or lower the blade.
- To adjust blade angle (bevel cut): Loosen the locking mechanism, tilt the blade to the desired angle (0-45 degrees), and then secure the locking mechanism.
5.2 Using the Parallel Stop and Angle Stop
The parallel stop is used for rip cuts, ensuring a consistent width. The angle stop is used for cross-cuts and miter cuts.
- Parallel Stop: Position the parallel stop to the desired cutting width and lock it in place using the eccentric clamp.
- Angle Stop: Insert the angle stop into the T-slot on the table. Adjust it to the required angle and secure it.
5.3 Performing a Cut
- Ensure the workpiece is stable and properly supported.
- Adjust the blade height so that the blade teeth are approximately 3-5mm above the workpiece.
- Turn on the saw using the green 'I' button. Allow the blade to reach full speed.
- Slowly and steadily feed the workpiece into the blade, using the parallel stop or angle stop for guidance. Always use the push stick for narrow cuts.
- Once the cut is complete, turn off the saw using the red 'O' button and wait for the blade to stop completely before removing the workpiece or offcuts.
6. Maintenance and Cleaning
Regular maintenance ensures the longevity and safe operation of your table saw.
6.1 General Cleaning
- Always disconnect the power plug before cleaning.
- Remove sawdust and debris from the saw table, blade guard, and motor housing after each use. Use a brush or vacuum cleaner.
- Do not use aggressive cleaning agents or solvents.
6.2 Blade Care
- Inspect the saw blade regularly for wear, damage, or dullness. Replace damaged or dull blades immediately.
- Clean resin and pitch buildup from the blade using a suitable blade cleaner.
6.3 Storage
Store the saw in a dry, secure location, out of reach of children. The power cable can be neatly stored using the integrated cable holder.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Saw does not start | No power supply; Faulty switch; Overload protection triggered. | Check power connection; Inspect switch; Allow motor to cool down and reset. |
| Blade binds in workpiece | Dull blade; Incorrect blade height; Workpiece not properly supported; Parallel stop not aligned. | Replace or sharpen blade; Adjust blade height; Ensure workpiece stability; Realign parallel stop. |
| Excessive vibration | Loose blade; Damaged blade; Loose components. | Check blade tightness; Replace damaged blade; Tighten all fasteners. |
| Poor cut quality | Dull or incorrect blade; Incorrect blade height; Material type. | Use appropriate sharp blade for material; Adjust blade height; Consider material properties. |
8. Technical Specifications
- Model: TC-TS 2025/1 U
- Power Input: 2000 W (Max. 1800 W continuous)
- Voltage: 240 V
- Saw Blade Diameter: 250 mm
- Saw Blade Bore: 30 mm
- Max. Cutting Height at 90°: 85 mm
- Max. Cutting Height at 45°: 65 mm
- Table Size: 640 x 487 mm
- Table Extension (Left/Right): Yes
- Weight: 18.8 kg
- Manufacturer Part Number: 4340540
9. Warranty and Support
Einhell products are subject to strict quality controls. Should this product nevertheless not function perfectly, please contact the Einhell service department or the dealer where you purchased the device.
For warranty claims, please retain your purchase receipt. Einhell offers an extended warranty on certain products upon online registration within 30 days of purchase. Please visit the official Einhell website for detailed warranty terms and registration information.
Online Support: For further assistance, FAQs, and spare parts, please visit the official Einhell website: www.einhell.com
