1. Introduction
This manual provides detailed instructions for the safe and efficient operation and maintenance of your Kegco XCK-1B Commercial Kegerator. Please read all instructions carefully before installation and use. Retain this manual for future reference.
The Kegco XCK-1B is a commercial-grade kegerator designed for dispensing beverages on tap. It features durable construction, efficient cooling, and a spacious interior. This unit is ETL and ETL Sanitation Listed and NSF Compliant, meeting recognized product safety standards for draft beer dispensers.
Figure 1: Front view of the Kegco XCK-1B Commercial Kegerator with single tap tower.
2. Safety Information
WARNING: To reduce the risk of fire, electric shock, or injury, follow these basic precautions:
- Read all instructions before using the appliance.
- Connect to properly grounded outlets only.
- Do not repair or replace any part of the unit unless specifically recommended in this manual. All other servicing should be referred to a qualified technician.
- Unplug the appliance before cleaning or performing any maintenance.
- Do not use this appliance near water or in excessively damp environments.
- Keep ventilation openings clear of obstruction.
- Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Ensure the unit is placed on a stable, level surface.
- Handle CO2 cylinders with care. Ensure proper ventilation when connecting or disconnecting CO2.
3. Product Overview and Features
The Kegco XCK-1B Kegerator is designed for commercial and home use, offering robust construction and efficient beverage dispensing.
Key Features:
- Commercial Grade: NSF compliant and ETL sanitation listed.
- Reliable Cooling: Powerful 1/7 hp compressor with forced air refrigeration ensures consistent temperatures throughout the cabinet and up to the faucet.
- Durable Construction: Steel construction with a brushed stainless steel top and a diamond plate floor designed to withstand frequent keg changes.
- Large Interior Capacity: Accommodates one full-size keg, up to two quarter slim kegs, or up to four 5-gallon kegs.
- External CO2 Tank Mount: Allows for larger CO2 tanks or saves interior space.
- Portability: Equipped with 4-inch locking casters for easy movement.
- Self-Closing Door: Features a magnetic gasket for positive door sealing and a lock for security.
- Integrated Drip Tray: Built-in drip tray with a drain and internal drain receptacle for easy cleaning.
- Air-Cooled Tower: Cold air is directed into the 3-inch diameter draft tower to minimize foam.
- Digital Temperature Control: Easy-to-use digital display with a temperature range of 33-43°F, programmable defrost, and alarm functions.
Figure 2: Overview of key features including drip tray, air-cooled tower, internal thermometer, digital display, and rubber floor mat.
4. Setup Instructions
4.1 Unpacking and Placement
- Carefully remove all packaging materials. Keep packaging for future transport if needed.
- Place the kegerator on a flat, level, and sturdy surface capable of supporting its weight when fully loaded.
- Ensure there is adequate ventilation around the unit (at least 4 inches of space on the sides and back) to allow for proper heat dissipation.
- Allow the unit to stand upright for at least 2-4 hours before plugging it in to allow refrigerants to settle.
4.2 Caster Installation
- The unit comes with 4-inch locking casters. Carefully tilt the unit and screw the casters into the designated holes at the bottom corners.
- Ensure all casters are securely tightened.
4.3 Draft Tower Installation
- The kegerator includes a 3-inch diameter draft tower. Position the tower over the opening on the top of the unit.
- Connect the beer line from the tower to the internal cooling system.
- Secure the tower to the top surface using the provided hardware.
4.4 CO2 Tank and Dispense Kit (Not Included)
This kegerator does not include a direct draw dispense kit. You will need to acquire a separate dispense kit and CO2 tank.
- Mount your CO2 tank externally using the provided knockout and mounting bracket. This allows for larger tanks and saves interior space.
- Connect the CO2 regulator to the CO2 tank and then connect the gas line to your dispense kit.
- Follow the instructions provided with your dispense kit for connecting the beer lines to the keg and the draft tower.
4.5 Keg Loading
Figure 3: Keg capacity configurations for the XCK-1B.
- Open the kegerator door. The interior features a durable diamond plate floor and a rubber floor mat to reduce shock.
- Carefully place the desired keg(s) inside the unit. The XCK-1B can hold one full-size (15.5 gal) keg, one pony size (7.75 gal) keg, two quarter slim (7.75 gal) kegs, or up to four 5-gallon kegs (with an external CO2 tank).
- Ensure kegs are stable and do not obstruct the door or internal components.
Figure 4: Interior view of the Kegco XCK-1B, illustrating space for kegs and internal cooling components.
5. Operating Instructions
5.1 Initial Power-On and Temperature Setting
- After allowing the unit to settle for 2-4 hours, plug the kegerator into a grounded electrical outlet.
- Locate the digital temperature control panel, typically on the back side of the unit.
- Use the controls to set your desired temperature. The optimal operating temperature range for most beverages is 33-43°F (0.5-6°C).
- The unit features a programmable defrost function, an alarm to alert you of notifications, and a night mode for energy saving. Refer to the digital controller's specific instructions for detailed programming.
Figure 5: Digital temperature display and control panel.
5.2 Dispensing Beverages
- Ensure your CO2 tank is connected, the regulator is set to the appropriate pressure (refer to your beverage's specific requirements, typically 10-12 PSI for beer), and the dispense kit is properly attached to the keg and tower.
- The air-cooled tower ensures that the beer lines remain cold all the way up to the faucet, reducing foam during pours.
- To dispense, pull the faucet handle forward. To stop, push the handle back.
Figure 6: Illustration of cold air circulation within the air-cooled tower to prevent foam.
6. Maintenance
6.1 Cleaning the Drip Tray
- The built-in drip tray with drain collects spills from the faucet.
- Any spills are routed into an internal drain receptacle. Regularly check and empty this receptacle.
- The drip tray features a removable grill for quick and easy cleaning. Wash with mild soap and water.
Figure 7: Detailed view of the drip tray and drain system.
6.2 Interior Cleaning
- Unplug the unit before cleaning.
- Wipe down the interior with a damp cloth and mild, food-safe cleaning solution.
- The rubber floor mat can be removed and cleaned separately. This mat helps reduce the shock of heavy kegs on the stainless steel floor.
- Ensure the interior is dry before plugging the unit back in.
6.3 Condenser Coil Cleaning
- Periodically clean the condenser coils located at the back or bottom of the unit. Dust and debris can accumulate, reducing cooling efficiency.
- Use a soft brush or vacuum cleaner to gently remove any buildup.
7. Troubleshooting
Before contacting customer support, review the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not operate | Not plugged in; circuit breaker tripped; power switch off. | Ensure unit is plugged in; reset circuit breaker; turn power switch on. |
| Temperature is not cold enough | Temperature set too high; door not closed properly; excessive door openings; poor ventilation; dirty condenser coils. | Adjust temperature setting; ensure door is sealed; minimize door openings; ensure adequate clearance around unit; clean condenser coils. |
| Excessive foam during dispensing | Beer lines not cold; incorrect CO2 pressure; dirty beer lines; warm keg. | Allow unit to cool completely; verify CO2 pressure settings; clean beer lines; ensure keg is adequately chilled. |
| Water on floor inside unit | Drain tube clogged; high humidity. | Clear any obstructions from the drain tube; this is normal in high humidity. |
8. Specifications
Refer to the following table for detailed product specifications of the Kegco XCK-1B Commercial Kegerator.
Figure 8: Dimensional drawing of the Kegco XCK-1B Kegerator.
| Specification | Value |
|---|---|
| Brand | Kegco |
| Model Number | XCK-1B |
| Item Weight | 143 pounds |
| Product Dimensions | 31 x 23.5 x 40 inches (D x W x H) |
| Capacity | 8.2 Cubic Feet |
| Installation Type | Freestanding |
| Form Factor | Tower |
| Special Features | Portable |
| Color | Black |
| Voltage | 115 Volts |
| Door Hinges | Right |
| Door Material Type | Stainless Steel |
| Certification | ETL |
| Included Components | Single Tap |
| Number Of Doors | 1 |
9. Warranty and Support
9.1 Warranty Information
For specific warranty details, please refer to the warranty card included with your product or contact Kegco customer support directly. Keep your proof of purchase for warranty claims.
9.2 Customer Support
If you have questions, require assistance with setup, or need troubleshooting beyond what is covered in this manual, please contact Kegco customer support. Our knowledgeable team is available during regular business hours to provide timely and reliable help.
You can typically find contact information on the manufacturer's website or on the product packaging.
