1. Introduction
This manual provides essential information for the proper setup, operation, and maintenance of your Hantek 6022BE 2-channel USB Digital Oscilloscope. The Hantek 6022BE is a PC-based instrument designed for electronic measurement and analysis, offering a 20 MHz bandwidth and a 48 MSa/s real-time sample rate. It connects to your computer via USB, utilizing software for waveform display and analysis.
2. Safety Information
Observe the following safety precautions to prevent injury and avoid damage to the instrument or connected devices:
- Power Source: The device is powered via USB. Ensure your computer's USB port provides stable power.
- Probe Usage: Use only the provided probes or compatible accessories. Ensure probes are correctly connected before applying power to the circuit under test.
- Environmental Conditions: Operate the oscilloscope in a dry environment, away from moisture, dust, and extreme temperatures.
- Maintenance: Refer all servicing to qualified personnel. Do not attempt to open or modify the device.
- Input Voltage Limits: Do not exceed the maximum input voltage ratings specified for the oscilloscope channels.
3. Package Contents
Verify that all items are present in your package:
- Hantek 6022BE USB Digital Oscilloscope Unit
- USB Cable
- Oscilloscope Probes (2 units)
- Software CD
- Quick Start Guide / Manual

Figure 3.1: Contents of the Hantek 6022BE package, including the oscilloscope unit, two probes, a USB cable, a software installation CD, and a user manual.
4. Setup
4.1 System Requirements
- Operating System: Windows 10, Windows 8, Windows 7, Windows NT, Windows XP, Vista.
- USB Port: Available USB 2.0 port.
4.2 Hardware Overview

Figure 4.1: Detailed view of the Hantek 6022BE's front and rear panels, highlighting Channel 1 (CH1), Channel 2 (CH2) BNC inputs, Probe Compensation Output, Ground Terminal, USBXI interface, and the USB socket for PC connection.
4.3 Driver and Software Installation
- Connect the Device: Connect the Hantek 6022BE to your computer using the provided USB cable.
- Install Drivers: Insert the software CD into your computer's optical drive. Navigate to the driver installation directory and run the setup file. Follow the on-screen instructions. Note: On Windows 10, you may need to temporarily disable driver signature enforcement if installation issues occur.
- Install Application Software: After driver installation, proceed to install the Hantek oscilloscope application software from the CD.
- Verify Installation: Once installation is complete, launch the Hantek software. The software should detect the connected oscilloscope.
4.4 Probe Connection
Connect the oscilloscope probes to the BNC input connectors (CH1 and CH2) on the front panel of the Hantek 6022BE. Ensure a secure connection. Calibrate probes as needed using the probe compensation output.
5. Operating the Oscilloscope
The Hantek 6022BE operates entirely through its PC software interface. Familiarize yourself with the software layout for effective use.
5.1 Basic Operation
- Launch Software: Start the Hantek oscilloscope application on your computer.
- Channel Selection: Enable or disable Channel 1 (CH1) and Channel 2 (CH2) as required for your measurement.
- Vertical Scale (Volts/Div): Adjust the vertical scale for each channel to properly display the amplitude of your signal.
- Horizontal Scale (Time/Div): Adjust the horizontal scale to view the desired time duration of the waveform.
- Trigger Settings: Configure the trigger source (CH1, CH2), trigger type (edge, pulse), and trigger level to stabilize the waveform display.
- Measurement Functions: Utilize the software's built-in measurement tools to analyze waveform parameters such as frequency, peak-to-peak voltage, RMS, etc.

Figure 5.1: The Hantek 6022BE in operation, connected to a computer, with the software displaying multiple signal waveforms for analysis.
5.2 Key Features
- Bandwidth: 20 MHz
- Real-time Sample Rate: 48 MSa/s
- Channels: 2 Analog Channels
- Interface: USB 2.0, USBXI standard for combined instrument setups.
6. Maintenance
Proper maintenance ensures the longevity and accuracy of your Hantek 6022BE oscilloscope.
- Cleaning: Use a soft, dry cloth to clean the exterior of the device. Do not use abrasive cleaners or solvents.
- Storage: Store the oscilloscope in a cool, dry place when not in use. Protect it from dust and physical impact.
- Probe Care: Handle probes carefully. Avoid bending or stressing the cables.
7. Troubleshooting
If you encounter issues, refer to the following common problems and solutions:
- Device Not Recognized:
- Ensure the USB cable is securely connected to both the oscilloscope and the computer.
- Try a different USB port on your computer.
- Verify that the drivers are correctly installed. Reinstall drivers if necessary.
- For Windows 10, temporarily disable driver signature enforcement during driver installation if issues persist.
- Software Not Launching or Crashing:
- Ensure your operating system meets the minimum requirements.
- Reinstall the application software.
- Check for updated software versions on the Hantek website.
- Inaccurate Measurements:
- Perform probe compensation to match the probe to the oscilloscope input.
- Ensure correct vertical and horizontal scale settings.
- Check probe attenuation settings (e.g., 1X, 10X) and ensure they match the software settings.
8. Specifications
| Feature | Specification |
|---|---|
| Model Name | 6022BE |
| Brand | Hantek |
| Analog Bandwidth | 20 MHz |
| Real-time Sample Rate | 48 MSa/s |
| Channels | 2 |
| Interface | USB 2.0, USBXI Standard |
| Operating System Compatibility | Windows 10, 8, 7, NT, XP, Vista |
| Material | Aluminum |
| Product Dimensions (L x W x H) | 23 x 17 x 0.1 cm (approximate, device only) |
| Product Weight | 720 grams (approximate, device only) |
| Recommended Uses | Electronics maintenance, research, and education |

Figure 8.1: Visual representation of the Hantek 6022BE highlighting its core technical specifications.
9. Warranty and Support
For warranty information, technical support, or further inquiries, please refer to the official Hantek website or contact your local distributor. General support resources may be found at Hantek Support.