Dabmar Lighting W8200-B Surface Mounted Wall Fixture

Introduction

Thank you for choosing the Dabmar Lighting W8200-B Powder Coated Steel Surface Mounted Wall Fixture. This fixture is designed for durability and provides efficient lighting for various applications. Please read this manual thoroughly before installation and operation to ensure proper use and safety.

Key Features:

• Powder coated steel surface mounted wall fixture
• Durable steel construction
• Clear, prismatic, heat resistant, polycarbonate lens
• Includes one (1) PL13 13-watt fluorescent lamp
• ETL approved for wet locations

Safety Information

Always follow basic safety precautions when installing, operating, and maintaining electrical fixtures to reduce the risk of fire, electric shock, and personal injury.

• WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installing or servicing.
• Ensure the fixture is properly grounded.
• Do not install this fixture in areas where it may be submerged in water.
• All wiring connections must be in accordance with local and national electrical codes (NEC).
• If you are unsure about the installation, consult a qualified electrician.
• Do not exceed the maximum wattage specified for the lamp.

Package Contents

Verify that all components are present and undamaged before beginning installation.

• 1 x Dabmar Lighting W8200-B Wall Fixture
• 1 x PL13 13-watt Fluorescent Lamp (pre-installed)
• Mounting Hardware (screws, anchors, etc. - typically included)

Image: Front view of the Dabmar Lighting W8200-B Powder Coated Steel Surface Mounted Wall Fixture, showing the black housing and the clear, prismatic polycarbonate lens with the fluorescent lamp visible inside.

Setup and Installation

Tools Required:

• Phillips head screwdriver
• Wire strippers
• Electrical tape
• Drill (if mounting to drywall/masonry)
• Pencil
• Safety glasses

Installation Steps:

1. Turn off Power: Locate the circuit breaker or fuse box and turn off the power to the wall switch or outlet where you will install the fixture. Verify power is off using a voltage tester.
2. Prepare Mounting Surface: Ensure the mounting surface is clean, dry, and structurally sound.
3. Attach Mounting Bracket: If applicable, attach the fixture's mounting bracket to the wall using the provided screws. Ensure it is level and secure.
4. Make Electrical Connections: Connect the fixture's wires to the corresponding house wires:
   • Connect the black (hot) wire from the fixture to the black (hot) wire from the wall.
   • Connect the white (neutral) wire from the fixture to the white (neutral) wire from the wall.
   • Connect the green or bare copper (ground) wire from the fixture to the green or bare copper (ground) wire from the wall.
   Secure connections with wire nuts and electrical tape.
5. Mount the Fixture: Carefully align the fixture with the mounting bracket and secure it with the provided screws. Ensure no wires are pinched.
6. Install Lamp: The PL13 13-watt fluorescent lamp is typically pre-installed. If not, gently insert the lamp into its socket, ensuring it is fully seated.
7. Restore Power: Once the fixture is securely installed and all connections are made, turn the power back on at the circuit breaker or fuse box. Test the fixture.

Operating Instructions

The Dabmar Lighting W8200-B fixture operates via a standard wall switch connected to its power source. Once installed and wired correctly, simply toggle the wall switch to turn the light on or off.

Maintenance

Cleaning:

To maintain the appearance and performance of your fixture, clean it regularly.

• Always disconnect power before cleaning.
• Wipe the exterior surfaces with a soft, damp cloth.
• Do not use abrasive cleaners, solvents, or polishes, as these may damage the finish or lens.
• Ensure the fixture is completely dry before restoring power.

Lamp Replacement:

The fixture uses one (1) PL13 13-watt fluorescent lamp. When the lamp reaches the end of its life or fails, replace it with a new one of the same type and wattage.

• Turn off power to the fixture at the circuit breaker.
• Carefully remove the polycarbonate lens (if applicable, refer to fixture design for access).
• Gently remove the old PL13 lamp from its socket.
• Insert the new PL13 13-watt fluorescent lamp, ensuring the pins align correctly with the socket.
• Replace the polycarbonate lens securely.
• Restore power and test the new lamp.

Troubleshooting

If you experience issues with your fixture, consult the table below for common problems and solutions.

Specifications

Warranty and Support

This Dabmar Lighting product is manufactured to high-quality standards. For specific warranty information, please refer to the documentation included with your purchase or visit the official Dabmar Lighting website. Keep your purchase receipt for warranty claims.

For technical support, replacement parts, or further assistance, please contact Dabmar Lighting customer service. Contact information can typically be found on the manufacturer's website or on the product packaging.

Online Resources: www.dabmar.com