Dabmar Lighting FG326-BZ Fiberglass Eye Lid Convex Well Light Instruction Manual

1. Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of the Dabmar Lighting FG326-BZ Fiberglass Eye Lid Convex Well Light. Please read this manual thoroughly before installation and retain it for future reference.

The Dabmar FG326-BZ is a durable in-ground well light designed for landscape and outdoor lighting applications. It features a bronze finish, a fiberglass body, and a clear, heat-resistant convex P.C. lens.

2. Safety Information

WARNING: Risk of electric shock. Installation should be performed by a qualified electrician in accordance with all local electrical codes and ordinances.

• Disconnect power at the circuit breaker or fuse box before installation or servicing.
• Ensure all wiring connections are secure and properly insulated.
• Do not install near flammable materials.
• This fixture is rated for in-ground soil and concrete applications. Ensure proper drainage to prevent water accumulation around electrical connections.
• Use only specified lamp types and wattages.
• Do not operate the fixture with a damaged lens or housing.

3. Package Contents

Verify that all components are present before beginning installation:

• Dabmar FG326-BZ Fiberglass Eye Lid Convex Well Light (Bronze Finish)
• Pre-wired UL listed wire/cable
• Installation hardware (screws, etc., as applicable)

Figure 1: The Dabmar FG326-BZ Fiberglass Eye Lid Convex Well Light. This image shows the bronze-finished housing with the clear, convex lens partially covered by an eyelid-style shroud, designed for in-ground installation.

4. Setup and Installation

The FG326-BZ well light is designed for in-ground installation in soil or concrete. Follow these general steps for proper setup:

1. Prepare the Location: Dig a hole in the desired location, ensuring it is deep enough to accommodate the fixture and allow for proper drainage. The fixture is rated for in-ground soil and concrete applications.
2. Wiring: The fixture comes pre-wired with UL listed wire/cable. Connect the fixture's wiring to your low-voltage landscape lighting system's main power cable. Ensure all connections are waterproof and comply with local electrical codes. Use appropriate wire connectors (not included) for outdoor use.
3. Positioning: Place the fixture into the prepared hole. Ensure the top surface of the fixture is flush with or slightly above ground level to prevent water pooling. The eyelid design directs light, so orient the fixture to achieve the desired illumination pattern.
4. Secure the Fixture: Backfill the hole with soil or concrete, ensuring the fixture is stable and level. If installing in concrete, follow standard concrete pouring and curing procedures.
5. Install Lamp (if not pre-installed): If a lamp is not pre-installed, carefully insert the correct PAR36 lamp type into the socket. Refer to the specifications for recommended lamp wattage.
6. Test: Restore power to the circuit and test the light fixture to ensure it functions correctly.

For optimal performance and longevity, ensure the installation site provides adequate drainage and is free from debris that could obstruct the light output or cause overheating.

5. Operating Instructions

The Dabmar FG326-BZ well light operates as part of a low-voltage landscape lighting system. Once properly installed and connected to a power source, the light will activate according to the control method of your overall system.

• Power Source: This fixture is designed for use with a corded electric power source, typically connected to a landscape lighting transformer.
• Control Method: The product specifications mention "App" as a control method. This refers to the control of the overall landscape lighting system, which may be managed via a smart app if your transformer or system controller supports it. The FG326-BZ itself is a passive light fixture that responds to the power supplied by the system.
• Activation: The light will turn on when power is supplied to the circuit it is connected to. This is typically controlled by a timer, photocell, or smart controller connected to your landscape lighting transformer.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your Dabmar FG326-BZ well light.

• Cleaning: Periodically clean the clear, heat-resistant P.C. lens and the bronze finish housing to remove dirt, debris, and mineral deposits. Use a soft cloth and mild soap and water. Avoid abrasive cleaners that could scratch the lens or damage the finish.
• Corrosion Resistance: The fixture is corrosion-resistant, making it suitable for ocean-front placement. However, regular rinsing with fresh water can help remove salt residue in coastal environments.
• Inspection: Annually inspect the wiring and connections for any signs of wear, damage, or corrosion. Ensure the fixture remains securely seated in the ground.
• Lamp Replacement: If the lamp burns out, disconnect power before replacing it. Allow the fixture to cool completely. Carefully remove the old lamp and insert a new PAR36 lamp of the correct wattage.
• Drainage: Ensure that the area around the fixture maintains good drainage to prevent water from accumulating and potentially affecting electrical components.

7. Troubleshooting

If your Dabmar FG326-BZ well light is not functioning as expected, consider the following:

If troubleshooting steps do not resolve the issue, contact Dabmar Lighting customer support or a qualified electrician.

8. Specifications

9. Warranty and Support

For warranty information or technical support regarding your Dabmar Lighting FG326-BZ fixture, please contact Dabmar Lighting directly through their official website or customer service channels. Keep your purchase receipt as proof of purchase.

For further assistance, you may visit the Dabmar brand page on Amazon.