Product Overview
The Makita CT226 12V max CXT® Lithium-Ion Cordless 2-Pc. Combo Kit provides two compact and efficient solutions for drilling, driving, and fastening tasks. This kit includes a two-speed driver-drill and a variable speed impact driver, both designed for superior ergonomics and reduced operator fatigue. The kit comes complete with two 12V max CXT 1.5Ah batteries and a charger, featuring a slide-style battery design that allows tools to stand upright for convenience.
Figure 1: Makita CT226 12V max CXT® Lithium-Ion Cordless 2-Pc. Combo Kit components.
Setup and Initial Use
1. Charging the Battery
Before first use, fully charge the 12V max CXT Lithium-Ion batteries. Insert the battery into the provided DC10WD charger. The charger's indicator lights will show the charging status. A full charge typically takes approximately 30 minutes for a 1.5Ah battery.
Figure 2: Makita DC10WD 12V max CXT Lithium-Ion Battery Charger.
2. Installing the Battery
Align the battery with the battery slot on the tool (either the Driver-Drill or Impact Driver) and slide it in until it clicks securely into place. To remove, press the release button on the battery and slide it out.
Operating Instructions
1. 3/8" Driver-Drill (FD05)
The FD05 Driver-Drill features two mechanical speed settings and a 3/8" keyless chuck.
- Speed Selection: Use the speed change lever located on top of the tool to select between Low Speed (1) for heavy-duty applications requiring high torque (0-450 RPM) and High Speed (2) for faster drilling (0-1,700 RPM).
- Chuck Operation: To install a drill bit or driver bit, twist the chuck counter-clockwise to open the jaws. Insert the bit and twist the chuck clockwise to tighten. Ensure the bit is centered and securely gripped.
- Torque Settings: The adjustable clutch ring allows you to select the desired torque setting for driving screws, preventing overtightening or stripping. For drilling, set the ring to the drill symbol.
Figure 3: Speed selection switch on the Driver-Drill.
Figure 4: 3/8" Keyless Chuck on the Driver-Drill.
Figure 5: Makita 12V max CXT Driver-Drill in use.
2. 1/4" Impact Driver (DT03)
The DT03 Impact Driver provides high torque for fastening applications.
- Bit Installation: Pull back the sleeve on the 1/4" hex chuck, insert the hex shank bit, and release the sleeve. The bit will lock into place.
- Variable Speed Trigger: The tool's speed and impact rate are controlled by the pressure applied to the trigger switch. Pressing the trigger further increases the speed (0-2,600 RPM) and impacts per minute (0-3,500 IPM).
- Forward/Reverse Switch: Use the lever above the trigger to select forward (clockwise) or reverse (counter-clockwise) rotation. Center position locks the trigger for safety.
Figure 6: 1/4" Hex Chuck on the Impact Driver.
3. Built-in L.E.D. Light
Both tools feature a built-in L.E.D. light that illuminates the work area when the trigger is pulled. The light remains on for a short period after the trigger is released.
Figure 7: Illuminated L.E.D. light on the Impact Driver.
Maintenance
- Cleaning: Regularly clean the tool's ventilation openings to prevent dust and debris buildup, which can affect performance and motor life. Use a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
- Battery Care: Store batteries in a cool, dry place away from direct sunlight and extreme temperatures. Do not store fully discharged batteries for extended periods. Charge them periodically if not in use.
- Storage: When not in use, store the tools and batteries in the provided tool bag or a secure, dry location out of reach of children.
- Inspection: Periodically inspect the power cord of the charger for damage. Check tools for loose screws or worn parts.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Tool does not operate. | Battery not charged or not properly inserted. | Ensure battery is fully charged and securely inserted. |
| Battery not charging. | Charger not plugged in; battery or charger fault. | Check power connection. If problem persists, contact Makita service. |
| Reduced power or performance. | Low battery charge; tool overheating; worn carbon brushes (not user serviceable). | Recharge battery. Allow tool to cool down. For persistent issues, contact Makita service. |
| Bit slips in chuck (Driver-Drill). | Chuck not tightened sufficiently; bit shank is dirty or damaged. | Retighten chuck firmly. Clean or replace bit. |
For issues not listed or if solutions do not resolve the problem, please contact Makita customer support or an authorized service center.
Specifications
| Feature | Detail |
|---|---|
| Model Number | CT226 |
| Voltage | 12 Volts (max CXT) |
| Battery Type | Lithium-Ion (1.5Ah) |
| Driver-Drill (FD05) Max Torque | 250 in.lbs. |
| Driver-Drill (FD05) No Load Speed | 0-450 / 0-1,700 RPM |
| Impact Driver (DT03) Max Torque | 970 in.lbs. |
| Impact Driver (DT03) No Load Speed | 0-2,600 RPM |
| Impact Driver (DT03) Impacts Per Minute | 0-3,500 IPM |
| Item Weight | 9.25 pounds (total kit) |
| Product Dimensions | 11.3 x 16.8 x 6 inches |
| Included Components | FD05 Driver-Drill, DT03 Impact Driver, (2) 1.5Ah Batteries, DC10WD Charger, Tool Bag |
Warranty and Support
This Makita product is covered by a 3-year limited warranty from the date of original purchase. This warranty covers defects in materials and workmanship. For full warranty details, terms, and conditions, please refer to the warranty card included with your product or visit the official Makita website.
For technical support, service, or to locate an authorized service center, please contact Makita customer service directly. Keep your proof of purchase for warranty claims.
You can visit the official Makita website for more information: www.makitatools.com
