Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your new Delta Essa Chrome Kitchen Faucet. Please read all instructions carefully before beginning installation to ensure proper function and to prevent injury or damage.
Safety Information
- Always turn off the main water supply before beginning any work on the faucet.
- Wear safety glasses during installation.
- If you are unsure about any step, consult a qualified plumber.
- Ensure all connections are tight to prevent leaks, but do not overtighten.
- Keep small parts away from children.
Package Contents
Verify that all components are present before beginning installation.
Image: Delta Essa Chrome Kitchen Faucet as packaged, showing main components.
- Delta Essa Kitchen Faucet Assembly
- Optional Deck Plate
- Mounting Hardware (washer, mounting nut, screws)
- Supply Lines (integrated)
- Sprayer Hose
- Sprayer Weight
- Foam Gasket
- Blue Clip
Specifications
Image: Diagram illustrating the dimensions of the Delta Essa faucet and installation hole requirements.
| Feature | Detail |
|---|---|
| Brand | DELTA |
| Model Name | Essa® |
| Model Number | 9113-DST |
| Finish Type | Chrome |
| Material | Metal |
| Number of Handles | 1 |
| Mounting Type | Deck Mount |
| Hole Count | 1 (or 3-hole with included deck plate) |
| Special Feature | Pull Down Sprayer |
| Maximum Flow Rate | 1.8 Gallons Per Minute |
| Spout Height | 15.75 Inches |
| Spout Reach | 9.25 Inches |
| Hose Length | 60 Inches |
| Item Weight | 6.56 pounds |
| Product Dimensions | 9.38"D x 11"W x 15.75"H |
Setup & Installation
Follow these steps for a successful installation. Refer to the provided videos for visual guidance.
Tools Required
- Phillips Screwdriver
- Adjustable Wrench
- Safety Glasses
- Flashlight
- Towel
- Pot or Bucket
- Silicone sealant (optional, for uneven surfaces)
Pre-Installation Steps
- Turn off the main water supply to your kitchen sink.
- Clear the area under the sink and place a towel and bucket to catch any residual water.
- Remove your old faucet (if applicable).
Mounting the Faucet
- Prepare the foam gasket: Separate the outer ring from the inner part. Peel off the backing to expose the sticky side.
- Feed the supply lines through the foam gasket, sticky side up. Seat the gasket flush on the bottom of the faucet.
- Feed the supply lines and sprayer hose down through the mounting hole in your sink. Position the faucet on the sink surface, ensuring the Delta logo is centered.
- From underneath the sink, slide the washer and mounting nut onto the sprayer hose and supply lines, pushing them up to the bottom of the faucet shank. Hand-tighten the mounting nut, ensuring hoses are not pinched.
- Use a Phillips screwdriver to tighten the mounting screws on the mounting nut. Tighten one screw, then the other, then re-check the first screw for tightness.
- If your sink surface is uneven, apply silicone sealant to the gasket before mounting for a watertight seal.
Video: Detailed installation guide for a single handle faucet, covering mounting and connections.
Video: Demonstrates how to mount the Delta faucet, including securing it to the sink.
Video: Important tip on avoiding a common installation error regarding handle placement.
Connecting Supply Lines
- Identify the hot (red) and cold (blue) supply lines from the faucet. Connect the blue line to the cold water supply valve (typically on the right) and the red line to the hot water supply valve (typically on the left). Hand-tighten the nuts.
- Use an adjustable wrench to give each nut one additional 360-degree revolution to ensure a secure connection. Do not overtighten.
- Manage excess tubing by looping it, ensuring the loop is at least 8 inches across to prevent kinks. Alternatively, use a spiral pattern.
Flushing Supply Lines
- Ensure the faucet handle is in the OFF position.
- Slowly turn on both the hot and cold water supply valves underneath the sink.
- Position a bucket under the sprayer hose outlet tube (the small tube where water will exit).
- Move the faucet handle to the full mix position and allow water to flush for approximately 30 seconds to clear any debris.
- Check all connections for leaks. Tighten any leaking connections.
Connecting Sprayer Hose & Weight
- Ensure the sprayer hose is free and clear of other supply lines to allow for smooth movement.
- Feed the sprayer hose through the sprayer weight.
- Push the end of the sprayer hose onto the outlet tube until it clicks into place. Secure it with the blue clip.
- Give the hose a gentle tug to ensure the connection is secure.
Operating Instructions
Image: The Delta Essa faucet in action, with the pull-down sprayer being used to rinse vegetables in a kitchen sink.
Water Flow and Temperature Control
The single handle controls both water flow and temperature. Move the handle left for hot water, right for cold water, and up/down to adjust flow.
Pull-Down Sprayer
The Essa faucet features a pull-down sprayer for extended reach. Simply pull the spray wand from the spout. MagnaTite® Docking uses a powerful integrated magnet to ensure the spray wand snaps securely into place when not in use.
Image: Close-up of the Delta Essa faucet demonstrating the MagnaTite® Docking system, where the spray wand is magnetically secured.
Spray Modes
Toggle between stream and spray modes using the button on the spray wand.
Image: Two views of the Delta Essa faucet, one showing water in spray mode and the other in stream mode.
Video: Product demonstration highlighting the features and spray modes of the Delta Essa faucet.
Maintenance
Cleaning the Faucet Finish
Clean the chrome finish with a soft, damp cloth. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the finish.
Touch-Clean® Spray Holes
The Touch-Clean® spray holes allow you to easily wipe away calcium and lime build-up with the touch of a finger, maintaining optimal spray performance.
Image: Close-up of the spray head showing the flexible rubber Touch-Clean® spray holes, designed for easy cleaning of mineral buildup.
Troubleshooting
Weak Water Stream
- Check for kinks in the supply lines or sprayer hose.
- Clean the aerator: Mineral deposits can restrict water flow. Gently unscrew the aerator from the spray head and rinse away any debris. Reinstall securely.
Leaks at Connections
- Ensure all supply line connections are hand-tightened, then given one additional wrench turn.
- Check the mounting nut underneath the sink for tightness.
- Verify the foam gasket is properly seated and, if necessary, apply silicone sealant for a better seal.
Sprayer Wand Does Not Dock Properly
- Ensure the sprayer weight is correctly installed on the hose underneath the sink, allowing for proper retraction.
- Check for any obstructions preventing the MagnaTite® magnet from engaging.
Warranty Information
Image: Icon representing the Lifetime Limited Warranty.
Delta faucets are backed by a Lifetime Limited Warranty, ensuring leak-free operation and finish durability for the life of the product. Refer to the official Delta Faucet website for full warranty details.
Customer Support
Image: A Delta Faucet customer service representative smiling, indicating support availability.
For further assistance or questions, please contact Delta Faucet Company customer service at 1-800-345-DELTA (3358) or visit their official website.
