Introduction
Thank you for choosing the Abu Garcia Max Pro Low Profile Baitcast Fishing Reel. This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your new fishing reel. Please read these instructions carefully before use to ensure optimal performance and longevity of your product.

Figure 1: Front view of the Abu Garcia Max Pro Low Profile Baitcast Fishing Reel, showcasing its compact design.
Setup
1. Attaching the Reel to a Fishing Rod
- Align the reel foot with the reel seat on your fishing rod.
- Tighten the reel seat nut securely until the reel is firmly attached and does not wobble.
2. Spooling Fishing Line
The Abu Garcia Max Pro reel is designed for braided fishing line. Ensure the line is spooled evenly and tightly to prevent issues like backlashing. The reel has a line capacity of approximately 130m/0.31mm, 115m/0.33mm, or 90m/0.370mm.
- Pass the line through the rod guides, starting from the tip.
- Tie the line to the reel spool using an arbor knot or similar secure knot.
- Engage the clutch.
- Maintain light tension on the line as you reel it onto the spool, ensuring it lays flat and even. Fill the spool to about 1/8 inch from the rim.

Figure 2: View of the machined double anodized aluminum spool, designed for strength and even line lay.
3. Adjusting the MagTrax Brake System
The MagTrax magnetic brake system provides consistent brake pressure throughout the cast, helping to prevent backlashes. Adjust the external dial to increase or decrease braking force. Start with a higher setting and gradually reduce it as you become more comfortable with casting.
4. Setting the Power Disk Drag System
The Power Disk drag system offers smooth and reliable drag performance. To set the drag, pull line directly from the reel while tightening or loosening the star drag knob. The drag should be set to approximately 25-30% of your line's breaking strength. This reel has a maximum drag of 6.8 kg (18 lb).
Operation
1. Casting
- Press the thumb bar to disengage the spool.
- Position your thumb on the spool to control line release.
- Make a smooth casting motion. As the lure flies, feather the spool with your thumb to prevent overruns and backlashes.
- Release your thumb pressure as the lure hits the water.
2. Retrieving
Turn the handle to engage the retrieve mechanism. The reel features a 7.1:1 gear ratio, providing a fast retrieve of 74 centimeters per turn. Maintain a steady retrieve speed appropriate for your lure and target species.

Figure 3: Side view of the reel, highlighting the 7.1:1 gear ratio for efficient line retrieval.
3. Fighting Fish
Allow the drag system to work by letting line out when a fish pulls hard, and retrieve line when the fish pauses or moves towards you. Avoid overtightening the drag, which can lead to line breakage or equipment damage.
Maintenance
1. Cleaning After Use
- After each use, especially in saltwater, rinse the reel with fresh water. Do not submerge the reel.
- Wipe the reel dry with a soft cloth.
- Remove any dirt, sand, or debris from the exterior and moving parts.
2. Lubrication
Regular lubrication ensures smooth operation and extends the life of your reel. Use high-quality reel oil and grease specifically designed for fishing reels.
- Apply a small drop of oil to the ball bearings (7 stainless steel ball bearings plus 1 roller bearing).
- Apply a thin layer of grease to the Duragear brass gear and other moving parts as recommended by Abu Garcia.
- Avoid over-lubrication, which can attract dirt.
3. Storage
Store your reel in a dry, cool place away from direct sunlight and extreme temperatures. Loosen the drag completely before storage to prevent compression of the drag washers.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Frequent Backlashes | Brake system set too low, spool tension too loose, improper casting technique, overfilled spool. | Increase MagTrax brake setting. Tighten spool tension knob slightly. Practice casting technique. Ensure spool is not overfilled. |
| Drag Slipping or Uneven | Drag washers are dry, dirty, or worn. Drag not set correctly. | Clean and re-grease drag washers. Adjust drag knob to desired setting. Replace worn washers if necessary. |
| Rough or Grinding Retrieve | Dirt or debris in gears/bearings. Lack of lubrication. Damaged components. | Clean and lubricate gears and bearings. Inspect for damaged parts. If problem persists, seek professional service. |
| Line Not Laying Evenly | Line guide obstructed or damaged. Improper line tension during spooling. | Check line guide for obstructions. Respool line with consistent tension. |
For issues not covered here or if problems persist, please contact Abu Garcia customer support or a certified reel technician.
Specifications
| Model Number | PMAX3 |
| Brand | Abu Garcia |
| Product Dimensions (L x W x H) | 16.51 x 15.88 x 17.3 cm |
| Item Weight | 0.21 kg (209 g) |
| Material | Stainless Steel, Aluminum, Graphite |
| Bearings | 7 Stainless Steel Ball Bearings + 1 Roller Bearing |
| Gear Ratio | 7.1:1 |
| Fishing Reel Line Retrieve | 74 cm per turn |
| Fishing Reel Maximum Drag | 6.8 kg (18 lb) |
| Line Capacity | 130m/0.31mm, 115m/0.33mm, 90m/0.370mm |
| Hand Orientation | Right Hand |
| Special Feature | Lightweight, MagTrax Brake System, Power Disk Drag System, Duragear Brass Gear |

Figure 4: Top view illustrating the approximate height of the reel (approx. 41mm).

Figure 5: Side view illustrating the approximate length of the handle (81mm).
Warranty & Support
Warranty information for your Abu Garcia Max Pro Low Profile Baitcast Fishing Reel is typically included with your purchase documentation. Please refer to those materials for specific terms and conditions.
For further assistance, technical support, or warranty claims, please contact Abu Garcia customer service directly. Contact details can usually be found on the manufacturer's official website or on the product packaging.