Feit Electric 988162

Download PDF
Contents

Feit Electric LED Retrofit Kit (Model 988162) Instruction Manual

Introduction

This instruction manual provides essential information for the safe and efficient installation, operation, and maintenance of your Feit Electric LED Retrofit Kit, Model 988162. This kit is designed to replace existing incandescent or halogen bulbs in 5-6 inch recessed can light fixtures, offering high-output LED illumination with significant energy savings.

Safety Information

Please read and understand all safety instructions before installation. Failure to follow these instructions may result in electric shock, fire, or other hazards.

  • WARNING: Risk of Electric Shock. Always turn off power at the circuit breaker or fuse box before beginning installation or performing any maintenance.
  • This product is intended for indoor use only. Do not use in wet locations unless specifically rated for such use.
  • Do not attempt to modify the product. Any alterations may void the warranty and create safety hazards.
  • Ensure the existing recessed can fixture is in good working condition and properly grounded.
  • Consult a qualified electrician if you are unsure about any part of the installation process.

Package Contents

Verify that all components are present before proceeding with installation:

  • 2 x Feit Electric LED Retrofit Kits (Model 988162)
  • 2 x Standard Base Adapters (E26 screw-in type)
Feit Electric LED Retrofit Kit with included standard base adapter

Image: Feit Electric LED Retrofit Kit shown with the standard screw-in base adapter.

Setup and Installation

Follow these steps to install your LED Retrofit Kit:

  1. Turn off power: Before starting, ensure the power to the light fixture is turned off at the circuit breaker.
  2. Remove existing bulb and trim: Carefully remove the old light bulb and any existing trim or baffle from the recessed can.
  3. Screw in base adapter: Screw the provided standard base adapter into the existing light socket within the recessed can.
  4. Connect terminal: Connect the terminal from the LED Retrofit Kit to the base adapter. Ensure a secure connection.
  5. Adjust spring clips (if necessary): For 5-inch recessed cans, the spring clips on the retrofit kit may need to be relocated to the inner position to ensure a proper fit. For 6-inch cans, the outer position is typically suitable.
  6. Insert fixture: Gently slide the LED Retrofit Kit into the recessed can, ensuring the spring clips engage with the can's interior.
  7. Push into place: Push the fixture firmly into place until it is flush with the ceiling surface. The trim is integrated into the fixture.
  8. Restore power: Turn the power back on at the circuit breaker.
Diagram showing three steps for easy installation of the LED retrofit kit: screw base adapter, connect terminal and slide fixture, push fixture into place.

Image: Step-by-step installation diagram for the LED Retrofit Kit.

Operating Instructions

The Feit Electric LED Retrofit Kit is designed for simple operation:

  • Power On/Off: Control the light using your standard wall switch.
  • Dimmable Functionality: This LED retrofit kit is dimmable. For optimal performance and to avoid flickering or buzzing, use with an LED-compatible dimmer switch.
  • Instant On: The light provides immediate full brightness upon activation.
  • Energy Efficiency: This LED kit uses significantly less energy compared to traditional incandescent or halogen bulbs, reducing electricity consumption.
Box side highlighting features: Uses up to 82% less energy, suitable for IC/Non-IC and Air Tight Housings, Mercury free, Instant on, full brightness, No ultraviolet, safe for artwork.

Image: Key features of the LED Retrofit Kit, including energy efficiency and safety.

Product box front showing 'LED Dimmable', '1250 Lumens', 'Soft White - 2700K', 'Replaces up to 120 Watt Flood Light', 'Uses only 21.5 Watts', and '85 degree beam angle'.

Image: Product packaging highlighting dimmable feature and light specifications.

Maintenance

The Feit Electric LED Retrofit Kit requires minimal maintenance.

  • Cleaning: Ensure power is off before cleaning. Wipe the fixture with a soft, dry, or slightly damp cloth. Do not use abrasive cleaners or solvents.
  • No User-Serviceable Parts: The LED components are integrated and not user-replaceable. Do not attempt to disassemble the fixture.

Troubleshooting

If you encounter issues with your LED Retrofit Kit, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Light does not turn on.No power to the fixture. Loose connection.Check circuit breaker. Ensure base adapter is securely screwed in and terminal connection is firm.
Light flickers or buzzes.Incompatible dimmer switch.Ensure you are using an LED-compatible dimmer switch. Some older dimmers may cause instability. A low-level buzz may occur at the lowest dimmer settings with certain dimmers.
Fixture does not fit into the recessed can.Spring clips are in the wrong position for the can size.For 5-inch recessed cans, relocate the spring clips to the inner position. For 6-inch cans, the outer position is typically correct.

Specifications

Detailed specifications for the Feit Electric LED Retrofit Kit (Model 988162):

FeatureDetail
Model Number988162
BrandFeit Electric
Light Source TypeLED
Wattage21.5 Watts
Equivalent WattageReplaces up to 120 Watt incandescent/halogen bulb
Brightness1250 Lumens
Color Temperature2700 Kelvin (Soft White)
Color Rendering Index (CRI)91+ CRI
DimmableYes
Beam Angle85 degrees (Flood)
Voltage120 Volts
Indoor/Outdoor UseIndoor
Special FeaturesMercury Free, RoHS Compliant, Instant On, No UV emissions, Safe for artwork, Suitable for damp locations
Estimated LifespanUp to 48 years (based on 3 hours/day)
CompatibilityReplaces 5-6 inch recessed cans (Type IC, Type Non-IC, Air Tight Housings)
Item WeightApproximately 0.01 Ounces per unit
UPC017801471434
Box side explaining 91+ Color Rendering Index (CRI) bulbs make colors appear as they really are, with an image of fruit in a basket.

Image: Explanation of 91+ Color Rendering Index (CRI) for accurate color representation.

Warranty Information

Warranty details for the Feit Electric LED Retrofit Kit (Model 988162) were not provided in the available product data. Please refer to the product packaging or the official Feit Electric website for specific warranty terms and conditions.

Support

Specific customer support contact information for the Feit Electric LED Retrofit Kit (Model 988162) was not provided in the available product data. For technical assistance, troubleshooting, or further inquiries, please visit the official Feit Electric website or contact their customer service department directly.

You can typically find support information on the manufacturer's website: www.feit.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.