Introduction
This manual provides essential instructions for the installation, operation, and maintenance of the Sensor Switch NPODM-2P-DX-WH nLight WallPod Switch. This device is a low-voltage, two-channel push-button wall switch designed for On/Off control and dimming (Raise/Lower) within an nLight lighting control system. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Safety Information
- WARNING: Risk of electric shock. Installation should only be performed by a qualified electrician in accordance with all national and local electrical codes.
- Disconnect power at the circuit breaker before installing or servicing the switch.
- Do not install in wet or damp locations.
- Ensure all wiring connections are secure and properly insulated.
- This device is designed for low-voltage applications. Do not connect to line voltage.
Setup and Installation
The NPODM-2P-DX-WH is designed for wall-mount installation. Follow these general steps for proper setup:
- Power Disconnection: Before beginning any installation, ensure that power to the circuit is turned off at the main circuit breaker.
- Mounting: The switch is designed to be wall-mounted. Secure the device to a standard electrical box using the provided screws and mounting brackets.
- Wiring: Connect the low-voltage wiring to the screw terminals on the back of the switch. Refer to the nLight system documentation for specific wiring diagrams and connections. Ensure proper polarity and secure connections.
- Faceplate Installation: Once the switch is securely mounted and wired, attach the decorative faceplate (not included) to complete the installation.
- Power Restoration: Restore power at the circuit breaker.
Operating Instructions
The NPODM-2P-DX-WH features two channels for control, typically configured for On/Off and dimming functions. The control method is touch-based via push buttons.
- On/Off Control: Press the designated On/Off button to toggle the connected lighting circuit between on and off states.
- Dimming (Raise/Lower): Use the dedicated Raise and Lower buttons to adjust the light output level. Press and hold the 'Raise' button to increase brightness, and press and hold the 'Lower' button to decrease brightness.
- nLight System Integration: This WallPod operates as part of an nLight lighting control system. Its functionality and configuration are managed through the nLight network, often utilizing Wi-Fi connectivity for system communication.
Maintenance
The Sensor Switch NPODM-2P-DX-WH requires minimal maintenance.
- Cleaning: To clean the plastic surface, gently wipe with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish.
- Inspection: Periodically inspect the switch for any visible damage or loose connections. If any issues are found, disconnect power and consult a qualified electrician.
Troubleshooting
If you experience issues with your NPODM-2P-DX-WH switch, consider the following common troubleshooting steps:
- No Response from Switch:
- Check if the circuit breaker supplying power to the switch is on.
- Verify that all low-voltage wiring connections are secure and correct.
- Ensure the switch is properly integrated into the nLight system and configured.
- Dimming Not Functioning:
- Confirm that the connected lighting fixtures are dimmable.
- Check nLight system settings to ensure dimming functionality is enabled and correctly assigned to the switch.
- Intermittent Operation:
- Inspect wiring for loose connections or damage.
- Check for potential interference with the Wi-Fi connectivity if applicable to the nLight system.
If problems persist after attempting these steps, contact a qualified electrician or the manufacturer's technical support.
Specifications
| Feature | Detail |
|---|---|
| Model | NPODM-2P-DX-WH |
| Brand | Sensor Switch |
| Switch Type | Dimmer Switch, Push Button |
| Operation Mode | Off (as a default state, controls On/Off and Dimming) |
| Contact Type | Normally Open |
| Connector Type | Screw Terminals |
| Terminal | Through Hole |
| Material | Plastic (housing), Metal (contact) |
| Item Dimensions (L x W x H) | 5.12 x 3.46 x 2.28 inches |
| Circuit Type | 2-way |
| Mounting Type | Wall Mount |
| Actuator Type | Push Button |
| Number of Positions | 2 (channels) |
| Controller Type | Push Button |
| Control Method | Touch |
| Connectivity Protocol | Wi-Fi (for nLight system integration) |
| Wattage | 250 watts (maximum load capacity) |
| Color | White (product variant) |
| Item Weight | 0.29 Pounds |
| International Protection Rating | IP54 |
| Specification Met | UL, cUL, IP54 |
| UPC | 745977911958 |
Warranty Information
According to product information, this Sensor Switch NPODM-2P-DX-WH is sold with No Warranty. Please verify warranty terms with your point of purchase or the manufacturer directly for the most current information.
Support
For technical assistance, further product information, or to report issues not covered in this manual, please contact Sensor Switch customer support or visit their official website. Always provide your product model number (NPODM-2P-DX-WH) when seeking support.