1. Introduction
The Harmar AL300 Fusion Lift is designed to transport both mobility scooters and power chairs on the rear of a vehicle. This lift provides a convenient and secure solution for transporting mobility devices, enhancing user independence. It features a robust design and user-friendly operation to ensure safe and reliable transport.
2. Safety Information
Read all instructions carefully before installation and operation. Failure to follow safety guidelines may result in injury or damage to the lift or vehicle.
- Vehicle Compatibility: It is critical to verify your vehicle's compatibility with the Harmar AL300 lift. This includes confirming the year, make, and model of your vehicle, the make and model of your mobility scooter or power chair, and the class of hitch installed (Standard Class III 2" X 2" or Class II 1.25" X 1.25").
- Hitch Height: Ensure your hitch height from the ground to the bottom of the installed hitch meets the minimum requirements (16" for a lift with Swing-Away, 18" for a lift without Swing-Away). If the hitch height is greater than 16", a Harmar Class III Hitch Post 5" Drop Adapter (Part# AL1235U) may be required.
- Weight Capacity: Do not exceed the lift's maximum weight capacity of 350 lbs. Overloading can cause damage to the lift, vehicle, or lead to unsafe operating conditions.
- Secure Device: Always ensure the mobility device is properly secured using all four self-tensioning Q’Straint retractors before driving.
- California Proposition 65 Warning: This product may expose you to chemicals including lead and lead components, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.p65warnings.ca.gov/.
3. Product Features
- Versatile Compatibility: Designed to carry virtually all scooters and power chairs.
- Secure Retractors: Equipped with four self-tensioning Q’Straint retractors for safe and reliable securing of your mobility device.
- No Modifications Required: Does not require modifications to your scooter or power chair.
- Automatic Platform Fold: When empty, the platform automatically folds up and out of the way with the flip of a single switch.
- Manual Crank Backup: Includes a manual crank backup for emergency operation.
- License Plate Mount: Integrated license plate mount.
- Swing-Away Option: The AL105 Swing-Away Joint (Class III) is included, allowing access to the vehicle's rear cargo area without removing the lift.
4. Setup and Installation
Proper installation is crucial for the safe operation of your Harmar AL300 lift. It is recommended that installation be performed by a qualified technician.
- Verify Compatibility: Before beginning, ensure your vehicle and mobility device meet all compatibility requirements as outlined in the Safety Information section.
- Hitch Receiver: The lift typically ships with a Class III Hitch receiver (2"x2"). Ensure your vehicle has a compatible hitch installed.
- Mounting the Lift: Securely attach the lift to your vehicle's hitch receiver according to the detailed instructions provided in the full installation manual.
- Electrical Connection: Connect the included wiring to your vehicle's battery. It is recommended to use 10 gauge wire and protect it with a quality automotive wire loom and self-resetting fuse for optimal performance and safety.
- Swing-Away Joint (AL105): If utilizing the swing-away feature, install the AL105 Swing-Away Joint as per its specific instructions. This joint allows the lift to pivot away from the vehicle for cargo access.
- Initial Test: After installation, perform a thorough test of all lift functions without a mobility device to ensure correct operation.
Image: The Harmar AL300 Fusion Lift in its operational position, attached to a vehicle's hitch receiver.
5. Operating Instructions
Follow these steps for safe and efficient operation of your Harmar AL300 lift.
- Lowering the Platform: Use the control switch to lower the lift platform to the ground level.
- Positioning the Mobility Device: Carefully drive or roll your scooter or power chair onto the center of the lift platform. Ensure it is positioned squarely and securely.
- Securing the Device: Attach all four self-tensioning Q’Straint retractors to the designated points on your mobility device and the lift platform. Ensure they are taut and the device is firmly held in place.
- Raising the Platform: Use the control switch to raise the platform until it is fully lifted and locked into the transport position. Verify that the mobility device is stable and secure.
- Folding the Platform (When Empty): If the lift is empty, the platform can be automatically folded up and out of the way by flipping a single switch. This reduces the overall length of the vehicle and improves visibility.
- Using the Swing-Away Feature: To access your vehicle's rear cargo area, engage the swing-away mechanism (AL105) according to its specific instructions. This will pivot the entire lift assembly away from the vehicle. Always ensure the lift is empty or the mobility device is securely fastened before swinging it away.
Image: The Harmar AL300 Fusion Lift with its platform in the lowered position, prepared for loading a scooter or power chair.
Image: The Harmar AL300 Fusion Lift with its platform folded vertically, demonstrating its compact storage when not in use.
6. Maintenance
Regular maintenance ensures the longevity and safe operation of your Harmar AL300 lift.
- Routine Inspection: Periodically inspect all moving parts, electrical connections, and securing straps for wear, damage, or corrosion.
- Cleaning: Keep the lift clean from dirt, debris, and road salt. Use a mild soap and water solution for cleaning.
- Lubrication: Lubricate pivot points and moving components as recommended in the comprehensive manufacturer's manual to ensure smooth operation.
- Fastener Check: Ensure all bolts, nuts, and fasteners are tight and secure.
7. Troubleshooting
This section provides general guidance for common issues. For complex problems, contact customer support.
- Lift Not Operating: Check all electrical connections, including the battery connection and fuse. Ensure the vehicle's ignition is on if required by your installation.
- Platform Not Moving Smoothly: Inspect for any obstructions or debris. Check for signs of wear on moving parts and ensure they are properly lubricated.
- Mobility Device Not Secure: Re-check all four Q’Straint retractors to ensure they are correctly attached and fully tensioned.
- Manual Crank Backup: In case of electrical failure, use the manual crank backup to operate the lift. Refer to the full manual for detailed instructions on using the manual crank.
8. Specifications
| Specification | Detail |
|---|---|
| Model | AL300 Fusion Lift |
| Brand | Harmar |
| Load Capacity | 350 Pounds |
| Item Weight | 120 Pounds |
| Material | Vinyl (referring to cover, main lift material is metal) |
| Vehicle Service Type | Street-Motor-Scooters |
| Manufacturer | Harmar Mobility |
9. Warranty and Support
For specific warranty information, please refer to the documentation included with your product or contact Harmar Mobility directly. For return policies and associated fees, please contact the seller from whom you purchased the Harmar AL300 lift.
For technical assistance, troubleshooting, or parts inquiries, please contact Harmar Mobility customer support through their official website or contact information provided in your product packaging.
