HornBlasters EH-OOGAH

HornBlasters Black Oogah Horn EH-OOGAH Instruction Manual

Model: EH-OOGAH

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your HornBlasters Black Oogah Horn, model EH-OOGAH. Please read these instructions carefully before installation and use to ensure safe and proper functionality. This horn is designed to produce the classic "Oogah" sound, adding a distinctive touch to your vehicle.

Safety Information

  • Always disconnect the vehicle's battery before performing any electrical work.
  • Ensure all wiring connections are secure and properly insulated to prevent short circuits.
  • Mount the horn in a location where it is protected from direct water spray and excessive heat.
  • Do not operate the horn for extended periods to prevent overheating.
  • Wear appropriate personal protective equipment, such as safety glasses, during installation.

Package Contents

  • 1 x HornBlasters Black Oogah Horn (Model EH-OOGAH)
  • Mounting hardware (bolt, nut)
  • Wiring components (relay, wires, connectors)
HornBlasters Black Oogah Horn with included components
Figure 1: HornBlasters Black Oogah Horn with included relay, wires, and mounting bolt.

Setup and Installation

The HornBlasters Black Oogah Horn is designed for easy installation with a 12V power source. Follow these steps for proper setup:

  1. Choose a Mounting Location: Select a secure, flat surface on your vehicle that is free from obstructions and away from excessive heat or direct water exposure. Ensure the horn's opening is not blocked.
  2. Mount the Horn: Use the provided bolt and nut to securely fasten the horn to the chosen location.
  3. Wiring Connections:
    • Connect the positive terminal of the horn to the positive wire from the included relay.
    • Connect the negative terminal of the horn to a suitable ground point on the vehicle chassis.
    • Connect the relay to your vehicle's 12V power supply (e.g., battery positive terminal) and the horn activation switch (not included). Refer to the relay's specific wiring diagram for detailed connections.
  4. Test Functionality: Once all connections are secure, reconnect the vehicle's battery and test the horn.
Video 1: An unboxing and basic wiring demonstration of a motor-driven Oogah/Klaxon horn, showing the connection of positive and negative terminals and a test of the sound.

Operating Instructions

The HornBlasters Black Oogah Horn produces a distinct, vintage "Oogah" sound. To operate the horn, activate the connected horn switch in your vehicle. The horn will emit its characteristic sound at approximately 115 decibels, ensuring attention-grabbing notification.

Maintenance

To ensure the longevity and optimal performance of your HornBlasters Oogah Horn, follow these simple maintenance guidelines:

  • Regular Cleaning: Periodically wipe down the exterior of the horn with a soft, damp cloth to remove dirt and debris. Avoid using harsh chemicals or abrasive cleaners.
  • Inspect Connections: Annually check all electrical connections for tightness and corrosion. Secure any loose connections and clean any signs of corrosion.
  • Check Mounting: Ensure the horn remains securely mounted to its location. Tighten any loose mounting hardware as needed.
  • Avoid Obstructions: Keep the horn's opening clear of any obstructions (e.g., mud, ice, debris) that could impede sound production.

Troubleshooting

If you encounter issues with your HornBlasters Oogah Horn, refer to the following troubleshooting tips:

ProblemPossible CauseSolution
Horn does not soundNo power, loose wiring, faulty relay, faulty horn switch.Check battery connections, ensure all wires are securely connected, test the relay and horn switch for functionality.
Weak or distorted soundLow voltage, poor ground connection, internal horn issue, obstruction in horn.Verify 12V power supply, ensure a clean and solid ground connection, check for obstructions, or contact support if the issue persists.
Horn sounds continuouslyStuck horn switch, faulty relay.Inspect and replace the horn switch if necessary, test or replace the relay.

Specifications

FeatureDetail
BrandHornBlasters
Model NumberEH-OOGAH
Product Dimensions (L x W x H)10 x 5 x 4 inches
Item Weight1.55 pounds
Voltage12 Volts
Noise Level115 Decibels
MaterialPlastic
Fit TypeUniversal Fit
UPC854916005136
Diagram showing the dimensions of the HornBlasters Oogah Horn
Figure 2: Product dimensions of the HornBlasters Oogah Horn.

Warranty and Support

For warranty information, technical support, or any questions regarding your HornBlasters Black Oogah Horn, please contact HornBlasters directly through their official website or customer service channels. Keep your purchase receipt for warranty claims.

© 2025 HornBlasters. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.