Enbrighten Z-Wave Plus 40-Amp Indoor/Outdoor Smart Switch (Model 14285) Instruction Manual

1. Product Overview

The Enbrighten Z-Wave Plus 40-Amp Direct-Wire Indoor/Outdoor Smart Switch is designed to integrate large load, hard-wired applications into a Z-Wave network. This heavy-duty switch enables wireless On/Off control for devices such as water heaters, landscape lighting, spas, pool pumps, and AC units. Suitable for both indoor and outdoor use, it features an easy-access wire connection block, front-mounted LED indicators for power and On/Off status, and a manual override switch. The device is housed in a lockable, tamper-resistant, weather-resistant metal enclosure, protecting internal components and settings from environmental factors and unauthorized access.

• Weatherproof: Rugged, wall-mount, metal NEMA-3R enclosure with a lockable door for outdoor use, protecting wiring and settings.
• Universal Use: Supports 120-277VAC and up to 40A. Configurable for single- or dual-load control for up to two 120VAC devices.
• Energy Monitoring: Remotely track Watts and kilowatt-hours when connected to a compatible Z-Wave hub that supports energy monitoring.
• Operation Modes: Integrated toggle switch allows manual, remote (Z-Wave), or OFF operation. Indicator LEDs display power status without opening the water-tight door.
• Easy-Access Wiring: Clearly numbered screw terminals provide secure connections, protected by a clear plastic guard.
• Environmental Conditions: Designed for outdoor use in dry, damp, or wet locations.

2. Safety Information

WARNING: RISK OF ELECTRIC SHOCK. This product requires installation by a qualified electrician. Always turn OFF power at the circuit breaker or fuse box before installation or servicing. Improper installation can result in serious injury or death.

• Ensure all wiring complies with national and local electrical codes.
• Do not exceed the maximum load rating of 40 Amps.
• Verify voltage compatibility (120-277VAC) before connecting.
• Keep the enclosure door closed and locked when not performing maintenance to maintain weather resistance and prevent tampering.

3. Package Contents

• Enbrighten Z-Wave Plus 40-Amp Indoor/Outdoor Smart Switch (Model 14285)
• Mounting Screws and Anchors
• Instruction Manual

4. Setup and Installation

This section provides detailed steps for physically installing the smart switch. Refer to the video below for a visual guide.

4.1 Tools Needed

• Hammer
• Level
• Wire Strippers
• Pliers
• Screwdrivers (Phillips and Flathead)
• Drill with appropriate drill bits

4.2 Preparing the Enclosure

1. Turn Off Power: Locate the circuit breaker or fuse box controlling the switch's intended location and turn off the power. Verify power is off using a voltage tester.
2. Select Knockouts: The enclosure features 1/2-inch and 3/4-inch knockouts. Choose the appropriate size based on your wiring.
3. Remove Knockouts: To remove a 1/2-inch knockout, place a small blade screwdriver into the inner ring and tap lightly. To expand to 3/4-inch, grasp the outer ring with pliers and gently twist until it breaks free.

Image: Enbrighten Z-Wave Plus 40-Amp Smart Switch showing its robust enclosure and control features.

4.3 Mounting the Switch

1. Choose Location: For optimal Z-Wave performance, mount the switch as close to your Z-Wave controller as possible. RF range can be affected by obstructions, metal objects, distance, and weather.
2. Orientation: Install the switch vertically with at least 4 inches of clearance above the housing to accommodate the antenna.
3. Mark Holes: Hold the box in place and mark the locations for the three mounting holes.
4. Drill Pilot Holes: Drill appropriate size pilot holes for your mounting surface. If installing on drywall, gently tap the provided anchors into place with a hammer.
5. Secure Box: Secure the box using the provided screws.
6. Attach Antenna: Slide the weather-resistant cover over the black antenna wire and tighten securely.

Image: Detailed dimensions of the Enbrighten Z-Wave Plus 40-Amp Smart Switch enclosure.

5. Wiring Configurations

Access the six terminals under the clear plastic guard inside the housing. For all configurations, wires should have a strip length of 1/2 inch, and screw terminals should be tightened to 25 inch-pounds force.

5.1 240VAC Single-Load, Energy-Monitored

• Connect 240V Line 1 to Terminal 1.
• Connect 240V Line 2 to Terminal 2.
• Connect the green or bare ground wire to the ground terminal.
• Using a jumper wire (not included), connect Terminals 3 and 5.
• Connect Load Line 1 from the device to Terminal 6.
• Connect Load Line 2 from the device to Terminal 4.

5.2 120VAC Single-Load, Energy-Monitored

• Connect the white neutral wire to Terminal 1.
• Connect the 120V black line to Terminal 2.
• Connect the green or bare ground wire to the ground terminal.
• Connect the white neutral from the device to Terminal 3.
• Connect the black load line from the device to Terminal 4.

5.3 120VAC Dual-Load, Load 1-Monitored

• Connect the white neutrals from the 120V power source and Load 2 to Terminal 1.
• Secure the black 120V line and one end of a jumper wire (not included) to Terminal 2.
• The other end of the jumper attaches to Terminal 5.
• Terminal 3 is reserved for the neutral wire of Load 1.
• Connect Load Line 1 to Terminal 4.
• Connect Load Line 2 to Terminal 6.

5.4 120VAC Dual-Load, Total of Both Loads Monitored

• Connect the 120V power source white neutral to Terminal 1.
• The 120V black line and one end of a jumper wire (not included) attach to Terminal 2.
• Secure the opposite end of the jumper wire to Terminal 5.
• Both neutral wires for the loads connect to Terminal 3.
• Attach Load Line 1 to Terminal 4.
• Attach Load Line 2 to Terminal 6.

Always close the plastic terminal guard when not securing connections. After wiring, ensure the weatherproof housing is closed and restore power at the circuit breaker or fuse box.

Image: Internal view of the smart switch, highlighting wiring terminals, ON/OFF/Z-Wave modes, and tamper-proof design.

6. Adding the Smart Switch to Your Z-Wave Network

To enable smart control, you must add the switch to a Z-Wave certified gateway (hub).

1. Prepare Your Controller: Follow your Z-Wave certified gateway's instructions to prepare your controller for pairing (inclusion mode).
2. Initiate Pairing: Once your hub is ready, press and release the program button on the smart switch to include it into the network.
3. S2 Security (if applicable): Some hubs offer an S2 security option. If prompted, enter the 5-digit Device Specific Key (DSK) security number found next to the QR code on the back of the packaging or inside the switch housing. The QR code can also be scanned if supported by your hub.

Image: Z-Wave Plus logo, signifying advanced smart home compatibility and features.

Image: Information on Z-Wave S2 Security and SmartStart, including a QR code for easy device inclusion.

Once successfully paired, you will have complete control over your connected device(s) according to groups, scenes, schedules, and interactive automations programmed through your Z-Wave controller. If your Z-Wave gateway features remote access, you can also control the switch remotely.

7. Operating Instructions

The Enbrighten Smart Switch offers flexible control options:

• Manual Control: Use the integrated toggle switch on the device to manually turn connected devices ON or OFF.
• Z-Wave Control: Once paired with a Z-Wave hub, control the switch wirelessly via your smart home app or voice commands (if integrated with voice assistants like Amazon Alexa or Google Assistant).
• Scheduled Events: Program schedules through your Z-Wave hub to automate On/Off times for connected devices.
• Energy Monitoring: Monitor energy consumption (Watts and kilowatt-hours) of connected loads through your compatible Z-Wave hub.

Image: The smart switch highlighting its quick-view status LEDs, manual override button, and weatherproof design.

Image: A tablet displaying energy monitoring data, illustrating the switch's capability to track power usage.

8. Maintenance

The Enbrighten Smart Switch is designed for durability and minimal maintenance. However, periodic checks are recommended:

• Terminal Check: Check all terminals 24 hours after installation to ensure specifications are still met and connections are secure.
• Enclosure Integrity: Periodically inspect the metal enclosure for any signs of damage or compromise to its weather-resistant seal.
• Cleaning: Clean the exterior of the enclosure with a damp cloth as needed. Do not use abrasive cleaners or solvents.
• Firmware Updates: Check your Z-Wave hub's documentation for any available firmware updates for connected devices, including this smart switch.

9. Troubleshooting

If you encounter issues with your Enbrighten Smart Switch, consider the following:

• No Power: Verify that power is restored at the circuit breaker or fuse box. Check all wiring connections for tightness.
• Device Not Responding: Ensure the switch is within range of your Z-Wave hub. Obstructions like thick walls or metal objects can reduce signal strength.
• Cannot Pair: Ensure your Z-Wave hub is in inclusion mode. Try moving the hub closer to the switch during pairing. If issues persist, try excluding the device from the network (even if it wasn't successfully included) and then re-attempt inclusion.
• Intermittent Control: This may indicate poor Z-Wave signal. Consider adding Z-Wave repeaters or repositioning your hub.
• Manual Override Not Working: Check the internal toggle switch to ensure it is not set to the 'Z-Wave' only mode.

10. Specifications

11. Warranty and Support

This Enbrighten product comes with a 2-year limited warranty. For warranty claims or technical support, please contact Jasco Products Company, LLC, the manufacturer. Refer to the product packaging or the manufacturer's website for the most current contact information and detailed warranty terms.