Introduction
Thank you for choosing the Project Source Chrome 2-Handle Shower Faucet with Single Function Showerhead. This manual provides essential information for the proper installation, operation, and maintenance of your new shower faucet. Please read this manual thoroughly before beginning installation or use to ensure safe and efficient operation.
Safety Information
- Always turn off the main water supply before installing, repairing, or servicing the faucet.
- Wear appropriate personal protective equipment, such as safety glasses and gloves, during installation.
- If you are unsure about any part of the installation process, consult a qualified plumber.
- Ensure all connections are secure to prevent leaks.
- Do not use abrasive cleaners or harsh chemicals on the chrome finish, as this may damage the surface.
Package Contents
Verify that all components are present before beginning installation:
- Shower Head
- Valve Assembly
- Hot and Cold Handles (2)
Image showing the Project Source Chrome 2-Handle Shower Faucet, featuring a chrome showerhead and two clear knob handles for hot and cold water control.
Setup (Installation)
This shower faucet is designed for a 1/2 inch IPS installation, suitable for mobile or modular homes. Professional installation is recommended.
- Prepare the Area: Turn off the main water supply to the shower area. Clear the work area and ensure you have all necessary tools.
- Remove Old Faucet (if applicable): Carefully remove any existing shower faucet components.
- Install Valve Assembly: Connect the valve assembly to the hot and cold water supply lines. Ensure all connections are tight and sealed to prevent leaks.
- Install Showerhead Arm: Secure the showerhead arm to the wall connection. Apply plumber's tape to threaded connections for a watertight seal.
- Attach Showerhead: Screw the single-function showerhead onto the showerhead arm. Hand-tighten, then use a wrench for a final snug fit, being careful not to overtighten.
- Install Handles: Attach the hot and cold knob handles to their respective valve stems.
- Test for Leaks: Slowly turn on the main water supply and check all connections for leaks. If leaks are present, tighten connections as needed.
Operating Instructions
The Project Source shower faucet features two knob handles for precise temperature control.
- Turning On/Off: Rotate either the hot (marked 'H') or cold (marked 'C') knob handle clockwise to turn off the water, and counter-clockwise to turn on the water.
- Adjusting Temperature: Adjust the hot and cold handles simultaneously to achieve your desired water temperature.
- Showerhead Function: The single-function showerhead provides a consistent spray pattern. No adjustments are needed for the spray type.
Maintenance
Regular cleaning and proper care will help maintain the appearance and functionality of your shower faucet.
- Cleaning the Finish: Clean the chrome finish with a soft, damp cloth and mild soap. Rinse thoroughly and dry with a soft cloth to prevent water spots. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can scratch or damage the finish.
- Showerhead Cleaning: If mineral deposits build up on the showerhead nozzles, gently rub them with your finger or a soft brush to dislodge the deposits. For stubborn buildup, a solution of equal parts white vinegar and water can be used.
- Drip-Free Cartridges: This faucet is equipped with drip-free cartridges designed for long-lasting, leak-free performance. If a drip occurs, contact customer support or a qualified plumber for cartridge replacement.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Low Water Flow | Clogged showerhead nozzles or debris in the water lines. | Clean showerhead nozzles. Check water supply valves are fully open. |
| Leaking from Faucet/Handles | Loose connections or worn cartridges. | Ensure all connections are tight. If leaking persists, cartridges may need replacement (contact support). |
| Water Temperature Issues | Incorrect adjustment of hot/cold handles or issues with water heater. | Adjust hot and cold handles. Check water heater settings. |
Specifications
- Brand: Project Source
- Model Number: 553400
- Finish: Chrome
- Material: Chrome, Plastic, Rubber (Showerhead), Brass (Handle Material)
- Installation Type: 1/2 in. IPS, Wall Mounted
- Number of Handles: 2
- Flow Rate: 1.75 Gallons Per Minute (GPM)
- Special Features: Drip-free cartridges
- Item Weight: 1.15 pounds
- Package Dimensions: 10.1 x 6.9 x 3 inches
- UPC: 820633962465
Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact Project Source customer service directly. Keep your purchase receipt for warranty claims.
For further assistance, you may also visit the retailer where the product was purchased.
