Introduction
This manual provides instructions for the installation, operation, and maintenance of your Denali Pure replacement refrigerator water filter. This filter is designed to be compatible with refrigerators requiring Maytag MFI2569VEM4 and UKF8001 filter cartridges, as well as other compatible models listed in the specifications section. Please read these instructions carefully before installation and retain them for future reference.

Image 1: The Denali Pure replacement refrigerator water filter. This image displays the cylindrical filter cartridge with the Denali Pure logo and product information label.
Safety Information
- Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
- This filter is intended for use with potable (drinkable) water only.
- Ensure the filter is installed correctly to prevent leaks.
- Replace the filter at recommended intervals to maintain optimal performance and water quality.
Setup and Installation
Pre-Installation Steps
- Locate your refrigerator's water filter compartment. This is typically inside the refrigerator, in the upper right corner, or in the base grille.
- Turn off the water supply to the refrigerator. This can usually be done by turning the shut-off valve behind the refrigerator or the main water supply to your home.
- Dispense water from the refrigerator dispenser for a few seconds to relieve any pressure in the water line.
Filter Installation
- Remove the old filter by twisting it counter-clockwise until it releases. Some water may drip out; have a towel ready.
- Remove the protective cap from the new Denali Pure filter.
- Insert the new filter into the filter housing. Align the arrow on the filter with the arrow on the filter housing.
- Twist the filter clockwise until it locks into place. You should feel it secure. Do not overtighten.
- Turn the water supply back on.

Image 2: Visual representation of the filter's design for easy, leak-free, and tool-free installation. The image highlights the filter's connection point, emphasizing its perfect fit and simple twist-in mechanism.
Flushing the System
After installation, it is important to flush the system to remove any air or carbon fines from the filter. Dispense approximately 2-3 gallons of water through the refrigerator's water dispenser. This process may take several minutes. The water may appear cloudy or discolored initially; this is normal and will clear up as the system flushes.
Operating Instructions
Once installed and flushed, your Denali Pure water filter will continuously filter water dispensed from your refrigerator. The filter utilizes a multi-layer filtration system, including coconut charcoal, to reduce various impurities.

Image 3: Illustration of the coconut charcoal filter technology. This image shows the filter alongside coconuts and charcoal, indicating the natural filtration media used to provide safe, clean, and great-tasting water by removing chemicals and pollutants.

Image 4: Diagram illustrating the multiple layers within the filter for efficient filtration. This graphic depicts several colored drops, each representing a different filtration stage, culminating in a clean water drop with the Denali Pure logo.
The filter is certified to NSF/ANSI Standard 42 for the reduction of chlorine, taste, and odor, ensuring improved water quality for drinking and ice making.
Maintenance
Filter Replacement Schedule
For optimal performance and to ensure continuous access to clean, filtered water, it is recommended to replace your Denali Pure water filter every 6 months or after filtering 300 gallons of water, whichever comes first. Your refrigerator may have an indicator light that signals when it's time to replace the filter.

Image 5: Reminder to replace the filter every 6 months for best performance. The image shows a woman holding a glass of water with a graphic indicating a 6-month replacement cycle.
Replacing the Filter
Follow the same steps as outlined in the "Setup and Installation" section to replace an old filter with a new one. Remember to turn off the water supply and flush the system after replacement.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Slow water flow from dispenser | Clogged filter, air in system, low water pressure | Flush the system for 2-3 gallons. If flow remains slow, replace the filter. Check household water pressure. |
| Water leaking from filter area | Filter not properly seated, damaged O-rings | Ensure filter is twisted fully clockwise and securely locked. Remove and re-install the filter. If leaking persists, contact support. |
| Bad taste or odor in water | New filter not flushed, filter needs replacement | Flush the system thoroughly (2-3 gallons). If taste/odor persists after flushing, replace the filter. |
| Filter indicator light remains on after replacement | Indicator light not reset | Refer to your refrigerator's owner's manual for instructions on how to reset the filter indicator light. This usually involves pressing and holding a specific button for a few seconds. |
Specifications
- Brand: Denali Pure
- Model Numbers: MFI2569VEM4, UKF8001
- Compatibility: Compatible with Maytag/Amana UKF8001, UKF8001-750, UKF8001AXX, UKF8001AXX-200, UKF8001AXX-750, UKF8001AXXP, UKF8001AXXT, UKF8001P, UKF8001T; Whirlpool WF50, OWF50, WF51, OWF51; Kenmore 46-9005, 469005, 9005, 9005P, 46-9006 and more.
- Filtration Media: Coconut Charcoal
- Operating Temperature: 33-100°F (0.6-38°C)
- Operating Pressure: 30-100 psi (207-689 kPa)
- Flow Rate: 0.5 GPM (1.9 LPM)
- Filter Life: 6 months or 300 gallons, whichever comes first.
- Certifications: Tested and Certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine, Taste, and Odor.

Image 6: List of compatible refrigerator models for the Denali Pure water filter. This image clearly displays the various Maytag/Amana, Whirlpool, and Kenmore model numbers that this filter is designed to replace.

Image 7: Certification details for the Denali Pure filter. This image highlights that the system is tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine, Taste, and Odor, featuring the 'Independently NSF Certified' seal.
Warranty and Support
Warranty Information
This Denali Pure replacement part is not an OEM product. All brand names and logos mentioned are registered trademarks of their respective owners and are used solely to illustrate compatibility. This product is not affiliated with any OEM brands and is not covered under any warranties offered by the original manufacturers. Any warranties for this product are offered solely by Denali Pure.
For specific warranty details, please refer to the packaging or contact Denali Pure customer support.
Customer Support
If you have any questions, require assistance with installation, or need troubleshooting help, please contact Denali Pure customer support. Contact information can typically be found on the product packaging or the official Denali Pure website.