Intex 28003

Download PDF
Contents

Intex 28003 Deluxe Pool Cleaning Kit Instruction Manual

Model: 28003

Introduction

The Intex 28003 Deluxe Pool Cleaning Kit is designed to help maintain the cleanliness of your above-ground pool. This comprehensive kit provides the necessary tools to effectively remove debris from both the pool floor and surface, ensuring a clean and enjoyable swimming environment.

Key features include:

  • Durable and corrosion-resistant plastic components.
  • An adjustable 279 cm (9.15 ft) aluminum telescopic pole, suitable for large pools.
  • A 6 m (19.7 ft) long, 3.2 cm (1.25 inch) diameter suction hose.
  • Multifunctional vacuum system for cleaning pool walls and bottom.
  • Equipped with a net, pole, vacuum brush, and hose for complete cleaning.
  • Connects directly to your filter pump for skimming and vacuuming.
Intex 28003 Deluxe Pool Cleaning Kit components

Image: All components of the Intex 28003 Deluxe Pool Cleaning Kit, including the telescopic pole, vacuum heads, brush, and net.

Setup Instructions

Before assembly, ensure you have an Intex filter pump with a minimum flow rate of 3,028 L/H (800 GPH). This kit is designed for use with Intex Above Ground pools 549 cm (18 ft) in diameter and larger.

  1. Assemble the Telescopic Pole: Connect the sections of the aluminum telescopic pole to achieve the desired length. Ensure all connections are secure.
  2. Attach Cleaning Head: Depending on the task, attach either one of the two vacuum heads or the 25.4 cm (10 inch) brush to the end of the telescopic pole. For surface cleaning, attach the bag net.
  3. Connect Suction Hose: Attach one end of the 7.50 m (24.6 ft) long, 32mm (1.25 inch) diameter hose to the cleaning head.
  4. Connect to Filter Pump: Connect the other end of the hose to the suction inlet of your Intex filter pump. Ensure a tight seal to prevent air leaks, which can reduce suction efficiency. Refer to your filter pump manual for specific connection points.
  5. Prepare for Operation: Submerge the cleaning head and hose into the pool water to remove any trapped air before turning on the filter pump. This helps ensure immediate and efficient suction.

Operating Instructions

Once the kit is properly set up and connected to your filter pump, you can begin cleaning your pool.

Using the Pool Vacuum (Bottom Cleaner)

  1. Ensure the vacuum head is attached to the telescopic pole and the hose is connected to the filter pump's suction inlet.
  2. Turn on your filter pump. The pump's force will create suction through the vacuum head.
  3. Slowly guide the vacuum head across the bottom of the pool. Overlapping strokes will ensure thorough cleaning.
  4. The vacuum head will draw in dirt particles and debris, which will then be filtered by your pump system.
  5. Avoid lifting the vacuum head out of the water while the pump is running, as this can introduce air into the system and reduce suction.

Using the Skimmer Net (Surface Cleaner)

  1. Attach the bag net to the telescopic pole.
  2. Use the net to skim the surface of the pool, collecting leaves, insects, and other floating debris.
  3. Periodically empty the collected debris from the net to maintain efficiency.

Maintenance

Regular maintenance of your cleaning kit will ensure its longevity and optimal performance.

  • Clean the Skimmer Net: After each use, empty and rinse the bag net thoroughly with fresh water to remove any trapped debris and prevent algae growth.
  • Rinse Components: Rinse the vacuum heads, brush, pole, and hose with fresh water after each use, especially if used with chlorinated water, to prevent corrosion and material degradation.
  • Inspect for Damage: Periodically inspect all components for signs of wear, cracks, or damage. Replace any damaged parts immediately to maintain cleaning efficiency and safety.
  • Proper Storage: Store the cleaning kit in a cool, dry place away from direct sunlight when not in use. Disassemble the pole if necessary for compact storage.
  • Filter Pump Maintenance: Remember to regularly clean or replace your filter pump's cartridge or sand, as the cleaning kit relies on the pump's filtration system to remove debris from the water.

Troubleshooting

If you encounter issues while using your Intex 28003 Deluxe Pool Cleaning Kit, consider the following common solutions:

  • Poor Suction:
    • Ensure your filter pump meets the minimum flow rate requirement (3,028 L/H).
    • Check all hose connections for leaks or loose fittings. Tighten as necessary.
    • Ensure the hose and vacuum head are fully submerged and free of trapped air before starting the pump.
    • Clean or backwash your filter pump's filter cartridge or sand, as a dirty filter can significantly reduce suction.
    • Inspect the hose for kinks or blockages.
  • Debris Not Being Collected:
    • For surface debris, ensure the skimmer net is not torn or damaged.
    • For bottom debris, verify that the vacuum head is making good contact with the pool floor.
    • Check for sufficient pump suction as described above.
  • Telescopic Pole Not Extending/Retracting Smoothly:
    • Rinse the pole sections with fresh water to remove any dirt or sand that might be causing friction.
    • Ensure the locking mechanisms are clean and functioning correctly.

Specifications

Feature Detail
Model Number 28003
Telescopic Pole Length 2.79 m (9.15 ft)
Suction Hose Length 7.50 m (24.6 ft)
Suction Hose Diameter 32 mm (1.25 inch)
Minimum Filter Pump Flow Rate 3,028 L/H (800 GPH)
Recommended Pool Diameter 5.49 m (18 ft) and larger
Material Type Aluminum, Plastic
Package Dimensions 114 x 32 x 13 cm (44.9 x 12.6 x 5.1 inches)
Package Weight 4 kg (8.8 lbs)
Manufacturer Intex

Warranty and Support

For information regarding product warranty, returns, or technical support, please refer to the official Intex website or contact Intex customer service directly. Keep your purchase receipt as proof of purchase.

You can visit the official Intex store for more products and support information: Intex Store

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.