Introduction
This manual provides essential information for the Dyson 917733-01 Brushroll Reset Switch. This component is designed as a direct replacement part for specific Dyson upright vacuum cleaner models, ensuring proper function of the brushroll system. Please read this manual thoroughly before attempting any installation or maintenance.
Product Overview
The Dyson 917733-01 Brushroll Reset Switch is a critical electrical component that controls the brushroll function in compatible Dyson vacuum cleaners. It is responsible for resetting the brushroll motor, often after an obstruction or overload, to prevent damage to the vacuum.
- Part Number: 917733-01 (Replaces part#: 916168-01)
- Function: Resets brushroll operation
- Compatibility: Designed for Dyson DC27, DC41, DC65, DC66, UP13, UP19, and UP20 series upright vacuum cleaners.
Figure 1: Front view of the Dyson 917733-01 Brushroll Reset Switch. This image shows the main body of the switch with its red push-button actuator and electrical terminals.
Figure 2: Rear view of the Dyson 917733-01 Brushroll Reset Switch. The back of the switch displays manufacturing details and electrical specifications.
Figure 3: Size comparison of the Dyson 917733-01 Brushroll Reset Switch. The image shows the switch held in a hand, indicating its compact size, approximately 1.6 inches (3 cm) in height.
Setup and Installation
Installation of the brushroll reset switch typically involves accessing the internal components of the vacuum cleaner. Due to the electrical nature of the part and the varying designs of Dyson models, it is highly recommended to consult the specific service manual for your Dyson vacuum model or seek assistance from a qualified technician. The following are general guidelines:
- Safety First: Always unplug the vacuum cleaner from the power outlet before attempting any installation or repair.
- Access the Switch: Locate the existing brushroll reset switch on your Dyson vacuum. This may require disassembling certain parts of the vacuum's housing. Refer to your vacuum's specific service manual for exact instructions on how to access this component.
- Disconnect Wiring: Carefully disconnect the electrical wires connected to the old switch. Note the orientation and connection points to ensure correct re-installation. Taking a photograph before disconnecting can be helpful.
- Remove Old Switch: Unmount the old switch from its housing.
- Install New Switch: Insert the new Dyson 917733-01 switch into the designated slot. Ensure it is securely seated.
- Connect Wiring: Reconnect the electrical wires to the new switch, matching the original configuration. Ensure all connections are firm and secure.
- Reassemble Vacuum: Carefully reassemble the vacuum cleaner, ensuring all screws and clips are properly secured.
Disclaimer: Improper installation can lead to electrical hazards or damage to the vacuum cleaner. If you are unsure about any step, please consult a professional.
Operating the Brushroll Reset Switch
The brushroll reset switch is an automatic safety feature. If the brushroll encounters an obstruction or becomes overloaded, the vacuum's internal system may trip the brushroll, causing it to stop spinning. To reset the brushroll:
- Unplug the Vacuum: Disconnect the vacuum from the power supply.
- Clear Obstruction: Inspect the brushroll area and clear any debris, tangled hair, or obstructions that may have caused the brushroll to stop.
- Press Reset Button: Locate the brushroll reset button (typically a small red button) on your vacuum cleaner. Press it firmly to reset the internal mechanism.
- Plug In and Test: Plug the vacuum back into the power outlet and turn it on. The brushroll should now operate normally.
If the brushroll continues to stop or the reset button does not function, further troubleshooting may be required.
Maintenance
The Dyson 917733-01 Brushroll Reset Switch is a sealed electrical component and requires no routine maintenance. Its lifespan is generally determined by the number of times it is tripped and reset. If the switch fails to reset the brushroll or exhibits intermittent behavior, it likely needs replacement.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Brushroll not spinning after clearing obstruction. | Brushroll reset switch not pressed, or switch is faulty. | Ensure the reset button is pressed firmly. If it still doesn't work, the switch may need replacement. |
| Brushroll stops frequently. | Frequent obstructions, worn brushroll, or faulty switch. | Regularly clear brushroll of debris. Check brushroll for wear. If issues persist, consider replacing the switch or having the vacuum inspected. |
| Reset button feels loose or unresponsive. | Internal mechanism of the switch is damaged. | The switch needs to be replaced. |
For persistent issues not resolved by these steps, it is advisable to contact Dyson customer support or a certified repair technician.
Specifications
| Attribute | Detail |
|---|---|
| Model Number | 917733-01 |
| Replaces Part # | 916168-01 |
| Dimensions (L x W x H) | Approximately 1 x 0.5 x 1 inches (2.54 x 1.27 x 2.54 cm) |
| Item Weight | 0.64 ounces (18.14 grams) |
| Controller Type | Push Button |
| Assembly Required | No (for the switch itself) |
| Batteries Required | No |
Warranty and Support
Information regarding the specific warranty for the Dyson 917733-01 Brushroll Reset Switch should be obtained from the point of purchase or directly from Dyson. For technical support, replacement part inquiries, or service, please visit the official Dyson website or contact their customer service department. Always provide your vacuum cleaner's model number and the part number (917733-01) when seeking support.
Dyson Official Website: www.dyson.com
