1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Metal Defender IP55 Dust and Water Resistant Walk-Through Metal Detector, Model TS-600. This device is designed for efficient and accurate detection of metallic objects in various environments, offering enhanced security.
The Metal Defender TS-600 features 6 independent detection zones, allowing for precise identification of metal locations on individuals passing through. Its robust design ensures durability and reliable performance.
2. Important Safety Information
Please read and understand all safety instructions before operating the Metal Defender TS-600. Failure to follow these instructions may result in injury or damage to the device.
- Installation: Ensure the unit is installed on a stable, level surface in an area free from strong electromagnetic interference.
- Power Supply: Use only the specified AC/DC power adapter. Do not overload electrical outlets.
- Environmental Conditions: The device is IP55 rated for dust and water resistance. However, avoid direct exposure to heavy rain or immersion in water. Operate within specified temperature and humidity ranges.
- Maintenance: Disconnect power before performing any cleaning or maintenance. Refer to the maintenance section for proper procedures.
- Children and Pets: Keep children and pets away from the device during operation.
- Medical Devices: Individuals with pacemakers or other medical implants should consult their physician before passing through the metal detector.
3. Product Overview
The Metal Defender TS-600 is a robust walk-through metal detector designed for reliable security screening. Key features include:
- 6 Independent Detection Zones: Red lights accurately indicate the area where metal is detected on a person.
- Adjustable Sensitivity: Maximum sensitivity can be programmed within 200 levels for precise screening.
- Traffic and Alarm Counter: Tracks and monitors the frequency of alarms and total traffic.
- IP55 Rating: Dust and water resistant for outdoor and indoor use.
- Dual Detection: Features transmitters and receivers in each panel for comprehensive scanning.
- High-Brightness LED Display: Clearly shows pass and alarm numbers.
Product Components
The Metal Defender TS-600 consists of two side panels and a control unit mounted at the top. The control unit houses the display and operational buttons.
Figure 1: Metal Defender TS-600 Walk-Through Metal Detector.
Figure 2: Key features and components of the Metal Defender TS-600.
Figure 3: Control Panel of the Metal Defender TS-600.
4. Setup and Installation
The Metal Defender TS-600 is designed for quick and easy assembly, typically within 15 minutes, with no specialized tools required.
- Unpacking: Carefully unpack all components and verify against the packing list.
- Placement: Choose a stable, level location for installation, away from large metal objects or sources of electromagnetic interference that could affect performance.
- Assembly: Connect the two side panels to the overhead control unit. Ensure all connections are secure.
- Power Connection: Connect the provided AC/DC power adapter to the unit and then to a suitable power outlet.
- Initial Power-On: Turn on the unit using the ON/OFF button on the control panel. The system will perform a self-test.
Figure 4: Quick setup time for the TS-600.
5. Operating Instructions
Once powered on, the Metal Defender TS-600 is ready for operation. The control panel allows for sensitivity adjustments and monitoring.
5.1. Control Panel Functions
- ON/OFF Button: Powers the unit on or off.
- PROG Button: Enters programming mode for sensitivity adjustments.
- UP/DOWN Buttons: Adjust sensitivity levels or navigate menu options in programming mode.
- LED Display: Shows the number of people who have passed through (traffic counter) and the number of alarms triggered (alarm counter).
- LED Indicator Bar: Provides a visual representation of detection strength.
5.2. Adjusting Sensitivity
The TS-600 offers 200 levels of sensitivity adjustment to suit various security requirements.
- Press the PROG button to enter programming mode.
- Use the UP or DOWN buttons to adjust the overall sensitivity level. Higher numbers indicate higher sensitivity.
- Individual zone sensitivity can also be adjusted for specific areas of the walk-through. Refer to the detailed programming guide for advanced settings.
- Press PROG again to exit programming mode and save settings.
Figure 5: Sensitivity adjustment feature.
5.3. Interpreting Detection Zones
When metal is detected, the corresponding red LED lights on the side panels will illuminate, indicating the approximate height of the metallic object. The TS-600 has 6 distinct zones.
Figure 6: Six independent detection zones.
5.4. Traffic and Alarm Counters
The LED display on the control unit shows two counters:
- Traffic Counter: Displays the total number of individuals who have passed through the detector.
- Alarm Counter: Displays the total number of times an alarm has been triggered.
These counters can be reset through the programming menu.
Figure 7: Traffic and alarm counter display.
5.5. Detection Speed
The Metal Defender TS-600 can achieve a maximum pass-through rate of up to 60 people per minute, depending on screening techniques and user interaction.
Video 1: Overview of Metal Defender TS-600 features, including detection speed and 6-zone capability. This video demonstrates the product's functionality and key specifications.
6. Maintenance
Regular maintenance ensures the longevity and optimal performance of your Metal Defender TS-600.
- Cleaning: Use a soft, damp cloth to wipe down the exterior surfaces. Do not use abrasive cleaners or solvents. Ensure the unit is powered off and unplugged before cleaning.
- Inspection: Periodically inspect all cables and connections for signs of wear or damage.
- Environmental Check: Ensure the operating environment remains within the IP55 rating limits (dust and water resistance) and recommended temperature/humidity.
- Software Updates: Check the manufacturer's website for any available firmware or software updates.
7. Troubleshooting
This section addresses common issues you might encounter with your Metal Defender TS-600.
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not power on. | No power, faulty power adapter, or power button issue. | Check power cable connection. Ensure outlet is functional. Try a different power adapter if available. |
| False alarms or excessive alarms. | Sensitivity too high, external interference, or nearby metal objects. | Reduce sensitivity settings. Relocate the unit away from large metal structures or electrical equipment. Ensure individuals remove all metallic items before passing through. |
| No detection or low sensitivity. | Sensitivity too low, unit malfunction. | Increase sensitivity settings. If the problem persists, contact customer support. |
| LED zone lights not working. | Faulty LED, internal connection issue. | Perform a system self-test. If lights remain non-functional, contact customer support. |
8. Specifications
| Feature | Detail |
|---|---|
| Model | TS-600 |
| Brand | Metal Defender |
| International Protection Rating | IP55 (Dust and Water Resistant) |
| Detection Zones | 6 Independent Zones |
| Sensitivity Levels | Up to 200 programmable levels |
| Power Source | AC/DC |
| Material | Metal |
| Color | Gray |
| Product Dimensions (H x W x D) | 87.5 inches x 32 inches x 15.5 inches |
| Item Weight | 87 Pounds |
9. Warranty and Support
The Metal Defender TS-600 comes with a 2-year warranty from the date of purchase, covering manufacturing defects. Additionally, Metal Defender provides free lifetime support for this product.
For technical assistance, troubleshooting, or warranty claims, please contact Metal Defender customer service. Refer to the official Metal Defender website for contact information.
Figure 8: Metal Defender brand commitment to support.
