Blackburn Local Bike Rear Light 15 Lumens

1. Introduction

This user manual provides essential information for the proper installation, operation, and maintenance of your Blackburn Local Bike Rear Light 15 Lumens. Please read this manual thoroughly before using the product to ensure optimal performance and safety. Retain this manual for future reference.

Key Features:

• ANSI FL-1 Standard Compliance: Designed to meet the ANSI FL-1 standard for consistent performance measurements in terms of output, run time, and water resistance.
• Universal Light Mount: Features a versatile silicone mount that accommodates diameters from 15-35mm, along with an integrated clip for attachment to clothing, bags, or racks.
• Excellent Side Visibility: Engineered with design features that channel bright light to each side, enhancing visibility to cross-traffic for improved safety.

2. Setup

Battery Installation:

The Blackburn Local Bike Rear Light operates on 2 AA batteries. To install or replace batteries:

1. Locate the battery compartment cover on the rear of the light unit.
2. Carefully open the cover.
3. Insert two AA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
4. Securely close the battery compartment cover.

Mounting the Light:

The light features a universal silicone mount and a clip for various attachment options.

Image 1: The Blackburn Local Bike Rear Light showing its silicone mounting strap.

• Seat Post Mount: Wrap the silicone strap around your bicycle's seat post. The flexible strap allows for secure attachment to seat posts with diameters between 15-35mm. Ensure the light is facing directly backward for optimal visibility.
• Clip Attachment: For alternative mounting, use the integrated clip to attach the light to clothing, backpacks, or bicycle racks. Ensure the light is firmly secured and visible from the rear.

Image 2: The Blackburn Local Bike Rear Light mounted on a bicycle rack, demonstrating its placement for rear visibility.

3. Operating Instructions

The Blackburn Local Bike Rear Light features multiple operating modes for varying visibility needs.

1. Power On/Off: Press the main button (which is the light face itself) once to turn the light on.
2. Mode Selection: With the light on, press the button repeatedly to cycle through the available modes:
   • Solid On: Provides a continuous beam of light.
   • Flash Mode: Emits a steady on/off flash pattern.
   • Strobe Mode: Produces several quick flashes followed by a brief pause.
3. Power Off: Continue pressing the button until the light turns off, or press and hold the button for approximately 2-3 seconds to power off directly from any mode.

The light's design ensures excellent side visibility, directing light to the sides to increase your presence to cross-traffic.

4. Maintenance

Cleaning:

To maintain optimal performance and appearance, regularly clean the light unit. Use a soft, damp cloth to wipe down the exterior. Avoid using abrasive cleaners or solvents, as these can damage the light's finish or lens.

Battery Care:

Replace batteries when the light appears dim or fails to illuminate. For prolonged storage, remove the batteries to prevent leakage and potential damage to the light.

Water Resistance:

The Blackburn Local Bike Rear Light is designed with a water-resistant rating of IPX1, meaning it is protected against vertically falling drops of water. While it can withstand light rain, it is not designed for submersion. Avoid exposing the light to heavy downpours or direct water jets for extended periods.

5. Troubleshooting

• Light does not turn on:
  • Check if the batteries are installed correctly with the proper polarity.
  • Replace old or depleted batteries with fresh AA batteries.
  • Ensure the battery compartment cover is securely closed.
• Light is dim or flickers:
  • This typically indicates low battery power. Replace the batteries.
  • Ensure battery contacts are clean and free of corrosion. Gently wipe them if necessary.
• Light detaches from mount:
  • Ensure the silicone strap is tightly secured around the seat post or the clip is firmly attached to its intended surface.
  • Verify that the mounting surface diameter is within the recommended 15-35mm range for the silicone strap.

6. Specifications

7. Warranty and Support

For specific warranty information regarding your Blackburn Local Bike Rear Light, please refer to the documentation included with your purchase or visit the official Blackburn website. Support resources, including FAQs and contact information, are typically available on the manufacturer's website.

Manufacturer: Blackburn

Website: www.blackburndesign.com