1. Introduction
This manual provides comprehensive instructions for the safe and effective use, maintenance, and troubleshooting of your Timco HC 818 Hair Clipper Kit. Please read this manual thoroughly before operating the device and retain it for future reference.
2. Package Contents
The Timco HC 818 Hair Clipper Kit includes the following components:
- 1 x Timco HC 818 Hair Clipper
- 4 x Interchangeable Cutting Combs (various sizes)
- 1 x Scissors
- 1 x Barber Comb
- 1 x Cleaning Brush
- 1 x Blade Protector
Figure 1: Overview of the Timco HC 818 Hair Clipper Kit, showing the main clipper unit, four guide combs, scissors, a barber comb, a cleaning brush, and a blade protector.
3. Important Safety Instructions
To reduce the risk of electric shock, injury, or fire, always follow these basic safety precautions:
- Read all instructions before using this appliance.
- Do not reach for an appliance that has fallen into water. Unplug it immediately.
- Do not use while bathing or in a shower.
- Unplug this appliance before cleaning.
- Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
- Use this appliance only for its intended use as described in this manual.
- Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged.
- Keep the cord away from heated surfaces.
- Never drop or insert any object into any opening.
- Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
- Always attach the plug to the appliance first, then to the outlet. To disconnect, turn all controls to OFF, then remove the plug from the outlet.
- Do not place or store the appliance where it can fall or be pulled into a tub or sink.
- Do not immerse the clipper in water or any other liquid.
4. Setup and Preparation
4.1 Initial Inspection
Upon unpacking, inspect all components for any signs of damage. Ensure all listed items in the "Package Contents" section are present.
4.2 Blade Oiling
Before first use, apply a few drops of clipper oil (not included) to the blades. This ensures smooth operation and prolongs blade life. Wipe off any excess oil.
4.3 Attaching Guide Combs
Select the desired cutting comb size. Align the comb with the clipper blades and push it firmly until it clicks into place. Ensure it is securely attached before use.
Figure 2: The Timco HC 818 Hair Clipper, illustrating its ergonomic design and power switch. This is the main unit to which guide combs are attached.
5. Operating Instructions
5.1 Powering On/Off
Plug the clipper into a suitable electrical outlet. To turn the clipper ON, slide the power switch to the 'I' position. To turn it OFF, slide the switch to the 'O' position.
5.2 Hair Cutting Techniques
- Ensure hair is clean and dry before cutting.
- Always start with a longer guide comb and gradually switch to shorter ones if a closer cut is desired.
- Hold the clipper with the blades pointing downwards.
- Move the clipper against the direction of hair growth for an even cut.
- Use the barber comb and scissors for detailing, blending, or longer hair sections.
- For precise lines, remove the guide comb and use the bare blades carefully.
Figure 3: A detailed view of the Timco HC 818 Hair Clipper blades, highlighting the cutting mechanism. Proper maintenance of these blades is crucial for optimal performance.
6. Maintenance and Care
6.1 Cleaning After Each Use
- Turn off and unplug the clipper.
- Remove the guide comb.
- Use the provided cleaning brush to remove loose hairs from the blades and clipper body.
- Wipe the exterior of the clipper with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.
6.2 Oiling the Blades
After every few uses, or if the clipper starts to pull hair, apply 1-2 drops of clipper oil across the top of the blades while the clipper is running. Allow it to run for a few seconds to distribute the oil, then turn off and wipe off excess.
6.3 Storage
Store the clipper and its accessories in a dry, cool place, away from direct sunlight and moisture. Always use the blade protector when storing the clipper to prevent damage to the blades.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Clipper does not turn on. | Not plugged in; power outlet issue; damaged cord. | Ensure clipper is securely plugged into a working outlet. Check for visible cord damage. |
| Clipper pulls or snags hair. | Blades are dull or not oiled; hair buildup between blades. | Clean and oil the blades. If problem persists, blades may need sharpening or replacement. |
| Clipper runs slowly or vibrates excessively. | Hair buildup; lack of lubrication. | Clean blades thoroughly and apply clipper oil. |
If the problem persists after attempting these solutions, please contact customer support.
8. Specifications
- Model: HC 818
- Brand: Timco
- Dimensions: 5.5 x 5.5 x 19 cm (approximately 2.17 x 2.17 x 7.48 inches)
- Weight: 480 g (approximately 1.06 lbs)
- Power Source: Corded Electric
- Included Accessories: 4 Interchangeable Cutting Combs, Scissors, Barber Comb, Cleaning Brush, Blade Protector
9. Warranty and Support
For warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support or inquiries regarding your Timco HC 818 Hair Clipper Kit, please visit the official Timco website or contact their customer service department.
Manufacturer: Timco
ASIN: B00WDXI8B0
