1. Introduction
This manual provides essential instructions for the safe and efficient operation, maintenance, and troubleshooting of your Pentair Flotec Stow & Flo All-in-One Emergency/General Utility Pump Kit. Please read this manual thoroughly before installation and use, and retain it for future reference.
The Flotec Stow & Flo kit is designed for emergency water removal and general utility pumping tasks, featuring a high-output pump, discharge hose, and a durable crate for storage and debris filtering.
2. Safety Information
WARNING: Failure to follow these safety instructions could result in electric shock, fire, serious injury, or death.
- Always disconnect power before servicing the pump.
- Do not operate the pump with a damaged cord or plug.
- Ensure the pump is properly grounded.
- Do not pump flammable or corrosive liquids.
- Keep children and unauthorized persons away from the pump during operation.
- This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
3. Package Contents
Verify that all components are present before proceeding with installation:
- High-output utility pump
- Large discharge hose
- Hose adapter
- Durable crate (for storage and debris filtering)
Figure 1: Overview of the Flotec Stow & Flo pump kit, including the pump, hose, and storage crate.
4. Setup Instructions
- Positioning the Crate: Place the durable crate in the area where water needs to be removed. The crate acts as a pre-filter to prevent large debris from entering the pump.
- Placing the Pump: Carefully place the utility pump inside the crate. Ensure the pump is stable and upright.
- Connecting the Hose: Attach the large discharge hose to the pump's outlet using the provided hose adapter. Secure the connection to prevent leaks during operation.
- Routing the Discharge Hose: Route the discharge hose to a suitable drainage area, ensuring the water will not re-enter the area being pumped. Avoid kinks or sharp bends in the hose.
- Power Connection: Connect the pump's power cord to a grounded 115-volt electrical outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for safety.
5. Operating Instructions
- Initiating Operation: Once the pump is set up and connected to power, it will begin pumping water automatically when the water level reaches the intake.
- Monitoring: Periodically check the pump's operation and the discharge area to ensure efficient water removal and prevent flooding in unintended locations.
- Stopping Operation: The pump will stop when the water level drops below its intake. To manually stop the pump, disconnect it from the power source.
- Continuous Use: The pump is designed for continuous duty within its specified limits. Avoid running the pump dry for extended periods, as this can cause damage.
6. Maintenance
Regular maintenance ensures the longevity and optimal performance of your pump kit.
- Cleaning: After each use, especially when pumping dirty water, rinse the pump and hose thoroughly with clean water. Remove any debris from the pump intake and the crate.
- Inspection: Periodically inspect the power cord, plug, hose, and pump housing for any signs of wear, damage, or corrosion. Replace damaged components immediately.
- Storage: When not in use, store the pump kit in a clean, dry, and frost-free location. The durable crate is designed for convenient storage of all components.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump does not start. | No power; tripped circuit breaker; clogged intake. | Check power connection and GFCI; reset breaker; clear intake. |
| Pump runs but no water is discharged. | Air lock; clogged hose; water level too low. | Ensure pump intake is submerged; clear hose; ensure adequate water level. |
| Reduced flow rate. | Partial clog in intake or hose; pump wear. | Clean intake and hose; inspect pump for wear. |
8. Specifications
| Brand | Pentair (Flotec) |
| Model Name | Flotec Stow & Flo All-in-One Emergency/General Utility Pump Kit |
| Model Number | FP0S2600RP |
| Voltage | 115 Volts |
| Maximum Discharge Flow | 2200 GPH (Gallons Per Hour) |
| Housing Material | Thermoplastic |
| Cord Length | 10 ft. |
| Power Source | AC Electric |
| Kit Weight | 10.45 Pounds |
| Item Dimensions (LxWxH) | 11.3 x 13.3 x 13.3 inches |
| UPC | 022315368446 |
Note on Power Source: While some general specifications may list 'Battery Powered', this pump operates on 115 Volts AC power, as indicated by specific voltage ratings and feature bullets.
9. Warranty and Support
Warranty: This product is covered by a manufacturer's warranty. For specific details regarding the warranty period and coverage, please refer to the documentation included with your purchase or contact Pentair customer support.
Manufacturer: Flotec (a Pentair brand)
For technical assistance, parts, or warranty claims, please contact Pentair customer support. Visit the official Pentair website for contact information.