Craftmade UCI-Remote Universal Remote Control

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Craftmade UCI-Remote Universal Remote Control. This remote is designed to provide convenient control over compatible Craftmade ceiling fans, allowing for adjustment of fan speeds and light functions.

Please read this manual thoroughly before attempting to install or operate the remote control to ensure proper function and safety.

2. Product Overview

Figure 1: Craftmade UCI-Remote Universal Remote Control Handset

This image displays the front of the Craftmade UCI-Remote. It is a black, elongated remote control with a central panel containing several oval-shaped buttons. From top to bottom, the buttons on the left column are labeled "HIGH", "MED", "LOW", and "OFF". On the right column, there are buttons labeled "L-1", "L-2", and "REV". Below these buttons, the word "Craftmade" is prominently displayed. At the very bottom of the central panel, there is a small horizontal slider switch.

2.1 Key Features

• Designed for use with select Craftmade fans only.
• Requires a compatible receiver to function (receiver not included).
• Provides 3-speed fan control (High, Medium, Low).
• Includes light control functions (L-1, L-2).
• Features a reverse function for fan direction.
• Sleek black finish.

3. Package Contents

The Craftmade UCI-Remote package includes:

• Craftmade UCI-REMOTE Handset (1 unit)

Note: Batteries are not included and must be purchased separately. A compatible fan receiver is also required for operation and is not included with this handset.

4. Setup and Installation

4.1 Battery Installation

1. Locate the battery compartment cover on the back of the remote control.
2. Slide or unclip the cover to open the compartment.
3. Insert the required batteries (typically AAA or 9V, refer to the remote's internal label if present) ensuring correct polarity (+/-).
4. Replace the battery compartment cover securely.

4.2 Pairing with Fan Receiver

This remote control must be paired with a compatible Craftmade fan receiver (e.g., Model UC7224T, if applicable) for proper operation. The pairing process typically involves setting DIP switches on both the remote and the receiver to match, or a learning function. Refer to your fan receiver's instruction manual for specific pairing procedures.

General Pairing Steps (May Vary by Receiver Model):

1. Ensure power to the ceiling fan is OFF at the circuit breaker.
2. Access the DIP switches on both the remote control (often inside the battery compartment) and the fan receiver.
3. Set the DIP switches on both devices to an identical pattern. Ensure no other remote in the vicinity uses the same pattern to avoid interference.
4. Restore power to the ceiling fan at the circuit breaker.
5. Within 30 seconds of restoring power, press and hold the "OFF" button on the remote control for approximately 5 seconds until the fan or light responds, indicating successful pairing.

If pairing is unsuccessful, repeat the steps, ensuring the DIP switch settings are identical and the timing is correct.

5. Operating Instructions

Once the remote control is paired with your fan receiver, you can operate your ceiling fan and light using the buttons on the handset:

• HIGH: Sets the fan speed to high.
• MED: Sets the fan speed to medium.
• LOW: Sets the fan speed to low.
• OFF: Turns the fan off.
• L-1: Controls light function 1 (e.g., turns light on/off, or adjusts brightness).
• L-2: Controls light function 2 (if applicable, e.g., a second light kit or dimming).
• REV: Reverses the direction of the fan blades (typically for seasonal use: clockwise for winter, counter-clockwise for summer).

Note: The exact functionality of light buttons (L-1, L-2) may depend on the specific fan and receiver model. Some may offer dimming by holding the button.

6. Care and Maintenance

To ensure the longevity and optimal performance of your Craftmade UCI-Remote, follow these simple maintenance guidelines:

• Cleaning: Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or internal components.
• Battery Replacement: Replace batteries promptly when the remote's range decreases or it becomes unresponsive. Always use the recommended battery type.
• Storage: If storing the remote for an extended period, remove the batteries to prevent leakage and corrosion. Store in a cool, dry place.
• Avoid Moisture: Keep the remote control away from water and high humidity.
• Avoid Extreme Temperatures: Do not expose the remote to extreme heat or cold.

7. Troubleshooting

8. Specifications

9. Warranty and Support

For information regarding product warranty, technical support, or replacement parts, please contact Craftmade customer service or visit the official Craftmade website. Keep your purchase receipt as proof of purchase for any warranty claims.

Craftmade Contact Information:

• Website: www.craftmade.com (Example link, actual link may vary)
• Customer Service: Refer to the website for current contact numbers or email.