1. Introduction
Thank you for choosing the Fluid Audio C5 2-Way 5 Inch Active Studio Monitor. This manual provides essential information for the proper setup, operation, and maintenance of your studio monitors. Please read this manual thoroughly before using the product to ensure optimal performance and safety.
2. Safety Instructions
- Power Source: Connect the unit only to a power supply of the type specified in this manual or on the unit. Ensure the voltage matches your region (110V or 220V).
- Ventilation: Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Water and Moisture: Do not use this apparatus near water or expose it to dripping or splashing.
- Heat: Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Cleaning: Clean only with a dry cloth.
- Servicing: Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
3. Package Contents
The Fluid Audio C5 2-Way 5 Inch Active Studio Monitor package includes:
- Fluid Audio C5 Studio Monitor Speaker (Pair)
- Detachable Power Cord
- Bare speaker wire
- 3.5mm headphone to RCA cable
- Acoustic Isolation Pads
4. Product Overview
4.1 Front Panel Overview
The front panel features the 5-inch woofer and 1-inch tweeter, designed for accurate sound reproduction. The woofer is responsible for low-frequency sounds, while the tweeter handles high frequencies.

Figure 1: Front view of the Fluid Audio C5 Studio Monitor.
4.2 Rear Panel Overview
The rear panel houses all the input connections, power switch, volume control, and acoustic tuning options. These controls allow you to adapt the monitor's sound to your specific listening environment.

Figure 2: Rear view of the Fluid Audio C5 Studio Monitor.
5. Setup
5.1 Placement
Position your C5 monitors on a stable surface, ideally at ear level, forming an equilateral triangle with your listening position. Ensure there is adequate space around the monitors for proper ventilation.
5.2 Connections
The C5 monitors offer various input options:
- Balanced Inputs: Use the 1/4-inch TRS or XLR inputs for professional audio interfaces and mixers. These connections minimize noise interference.
- Unbalanced Inputs: Use the RCA input for consumer-grade audio equipment.
Connect the power cord to the AC input on the rear panel and then to a suitable power outlet.
5.3 Acoustic Tuning
The rear panel features controls to adjust the monitor's frequency response to your room acoustics:
- Volume: Adjusts the overall output level.
- Mid: Adjusts the mid-range frequencies.
- High: Adjusts the high-range frequencies.
- Low Cutoff: Filters out low frequencies, useful when paired with a subwoofer.
- Acoustic Space: Compensates for bass buildup when monitors are placed near walls or corners.
6. Operating Instructions
- Ensure all audio connections are secure before powering on.
- Turn the volume knob on the rear panel to its minimum setting.
- Flip the power switch to the 'On' position.
- Gradually increase the volume to your desired listening level.
- When finished, turn the volume down before powering off the monitors.
7. Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the monitors. Avoid abrasive cleaners or solvents.
- Dust: Regularly dust the drivers and vents to prevent accumulation.
- Environment: Keep the monitors in a dry environment, away from extreme temperatures and direct sunlight.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No Sound | Power off, incorrect input, volume too low. | Check power connection, select correct input, increase volume. |
| Distorted Sound | Input signal too high, faulty cable. | Reduce input level, try a different cable. |
| Hum or Buzz | Ground loop, unshielded cables. | Use balanced cables, check grounding, try different power outlets. |
9. Specifications
| Feature | Specification |
|---|---|
| Speaker Type | 2-Way Active Studio Monitor |
| Woofer Diameter | 5 Inches |
| Tweeter Diameter | 1 Inch |
| Amplifier Power | 2 x 20 Watts (40W total) |
| Frequency Response | 54 Hz - 22 kHz |
| Crossover Frequency | 4.5 kHz |
| Signal-to-Noise Ratio | > 90 dB (A-weighted) |
| Input Impedance | 20 k ohms balanced, 10 k ohms unbalanced |
| Input Voltage | Fixed 110V ~50/60 Hz or 220V~50/60 Hz |
| Connectivity Technology | RCA, TRS |
| Item Weight | 10 Pounds |
10. Warranty and Support
The Fluid Audio C5 Studio Monitor comes with a 2-year limited warranty. For warranty claims or technical support, please refer to the contact information provided with your purchase documentation or visit the official Fluid Audio website.