Product Overview
The Winegard RP-SK21 is a crucial replacement component designed for the Winegard TRAV'LER SK-1000 RV satellite antenna. This assembly includes both the reflector bracket and the Low Noise Block (LNB) converter, which are essential for receiving satellite signals.
It serves as a direct replacement for damaged or worn-out parts on your existing SK-1000 system. Additionally, it can be utilized with the Winegard RP-SK11 to convert a TRAV'LER SK-SWM3 system to be compatible with DISH programming. The LNBs included may be remanufactured.
This assembly is compatible with DISH Network satellites at 110° (SD/HD), 119° (SD/HD), and 129° (SD/HD), ensuring broad compatibility for DISH programming.
An image showing the Winegard RP-SK21 Replacement Reflector Bracket and LNB Assembly, including the main arm, LNB housing, base plate, various bolts, and coaxial cables. This assembly is vital for satellite signal reception.
What's in the Box
The Winegard RP-SK21 package typically includes the following components:
- Feed arm assembly (includes reflector bracket and LNBs)
- Necessary mounting hardware (bolts, washers, etc.)
- Coaxial cables for LNB connections
Note: Contents may vary slightly. Please inspect your package upon arrival to ensure all components are present.
Installation and Setup
This section provides general guidelines for installing the RP-SK21 assembly. Professional installation is recommended for optimal performance and safety.
- Safety First: Ensure the RV satellite system is powered off and disconnected from any power sources before beginning installation.
- Remove Old Assembly: Carefully detach the existing reflector bracket and LNB assembly from your Winegard TRAV'LER SK-1000 system. Note the routing of all cables and the position of mounting hardware.
- Mount New Assembly: Align the new RP-SK21 feed arm assembly with the mounting points on your TRAV'LER dish. Secure it using the provided hardware. Ensure all connections are tight but do not overtighten.
- Connect LNB Cables: Connect the coaxial cables from the LNBs to the appropriate ports on the satellite dish's main unit. Ensure secure, hand-tight connections.
- Cable Management: Route all cables neatly and secure them to prevent snagging or damage during operation or travel.
- System Test: Once the physical installation is complete, power on your Winegard TRAV'LER system and perform a satellite acquisition test to confirm proper signal reception. Refer to your TRAV'LER SK-1000 user manual for detailed system testing procedures.
For detailed, model-specific installation instructions, please refer to the official Winegard TRAV'LER SK-1000 installation manual or consult a qualified technician.
Operation
The Winegard RP-SK21 is a passive component that facilitates satellite signal reception. Its operation is integrated with the overall functionality of your Winegard TRAV'LER SK-1000 RV satellite antenna system.
- Signal Acquisition: The LNBs within the RP-SK21 assembly receive the satellite signals, which are then processed by the TRAV'LER system.
- DISH Compatibility: This assembly is specifically designed to work with DISH Network programming, supporting 110°, 119°, and 129° satellites.
- Automatic Functionality: Once installed and the TRAV'LER system is powered on, the assembly works automatically as part of the satellite acquisition and tracking process.
No direct user interaction is required with the RP-SK21 assembly itself during normal operation.
Maintenance
Regular maintenance helps ensure the longevity and optimal performance of your RP-SK21 assembly and the entire satellite system.
- Visual Inspection: Periodically inspect the reflector bracket and LNBs for any signs of physical damage, corrosion, or loose connections.
- Cleaning: Gently clean the LNB surfaces and the bracket with a soft, damp cloth to remove dirt, dust, or debris. Avoid abrasive cleaners or harsh chemicals.
- Cable Integrity: Check all coaxial cable connections for tightness and ensure the cables are not frayed or pinched.
- Environmental Protection: While designed for outdoor use, extreme weather conditions can impact performance. Ensure the system is properly stowed when not in use or during travel.
Do not attempt to disassemble the LNBs or the sealed components of the assembly, as this may void the warranty and damage the unit.
Troubleshooting
If you experience issues with your satellite reception after installing the RP-SK21, consider the following common troubleshooting steps:
- No Signal/Poor Signal:
- Verify all coaxial cable connections are secure and correctly attached.
- Ensure there are no obstructions (trees, buildings) blocking the line of sight to the satellites.
- Confirm the TRAV'LER system has successfully acquired the correct DISH satellites (110°, 119°, 129°).
- Check the main TRAV'LER control unit for any error codes or messages.
- Intermittent Signal:
- Inspect the LNBs and bracket for any physical damage or loose components that might be affected by wind or vibration.
- Ensure the RV is level and stable, as movement can affect signal lock.
- Incorrect Programming:
- If you used the RP-SK21 with an RP-SK11 to convert from SWM3, ensure the system's internal settings are correctly configured for DISH programming.
If issues persist after performing these checks, it is recommended to contact Winegard Customer Support or a certified RV satellite technician.
Specifications
| Model Number | RP-SK21 |
| Compatibility | Winegard TRAV'LER SK-1000 RV Satellite Antenna, Winegard TRAV'LER SK-SWM3 (with RP-SK11 for DISH conversion) |
| Compatible Satellites | DISH: 110° (SD/HD), 119° (SD/HD), 129° (SD/HD) |
| Product Type | Auto Accessory / Replacement Satellite Dish Component |
| Item Weight | 8.8 pounds (approx.) |
| Product Dimensions | 11.25 x 11.25 x 25.5 inches (approx.) |
| Country of Origin | United States |
Warranty Information
Winegard products are typically covered by a manufacturer's warranty. The specific terms and duration of the warranty for the RP-SK21 assembly may vary.
For detailed warranty information, including coverage, limitations, and how to make a claim, please refer to the documentation included with your original Winegard TRAV'LER system or visit the official Winegard website.
Retain your proof of purchase for warranty purposes.
Customer Support
If you require further assistance with installation, troubleshooting, or have questions regarding your Winegard RP-SK21 Replacement Reflector Bracket and LNB Assembly, please contact Winegard Customer Support.
You can typically find contact information (phone numbers, email, support portals) on the official Winegard website:
Visit Winegard's Official Website
When contacting support, please have your product model number (RP-SK21) and any relevant purchase details ready.
