Introduction
This manual provides comprehensive instructions for the safe and efficient operation, maintenance, and troubleshooting of your AstralPool Pulit Advance +5 Robotic Pool Cleaner. Please read this manual thoroughly before using the appliance.
Image: The AstralPool Pulit Advance +5 Robotic Pool Cleaner, a blue and dark blue unit with a handle, designed for efficient pool cleaning.
Important Safety Instructions
- Always disconnect the power supply before performing any maintenance or cleaning.
- Do not operate the cleaner if the power cable is damaged.
- Ensure the power supply unit is placed at least 3.5 meters (11.5 feet) from the edge of the pool.
- Do not enter the pool while the cleaner is operating.
- This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Setup and Initial Use
Unpacking
Carefully remove all components from the packaging. Verify that all parts are present:
- Pulit Advance +5 Robotic Pool Cleaner unit
- Power supply unit
- 18m self-floating cable
- Transport caddy
- PVA brushes
- Standard filter cartridges (fine and coarse filters available separately)
Image: The AstralPool Pulit Advance +5 cleaner shown with its transport caddy and the coiled self-floating cable, ready for setup.
Connecting the Cleaner
- Place the power supply unit in a shaded area, at least 3.5 meters (11.5 feet) from the pool edge.
- Connect the self-floating cable to the cleaner unit. Ensure a secure connection.
- Connect the other end of the self-floating cable to the power supply unit.
- Plug the power supply unit into a grounded electrical outlet.
Operating Instructions
Placing the Cleaner in the Pool
Gently lower the cleaner into the pool. Allow it to sink to the bottom, releasing any trapped air bubbles. Ensure the cable is not tangled.
Image: A front view of the AstralPool Pulit Advance +5, highlighting its compact design and the "Powered by Aquabot" branding.
Starting a Cleaning Cycle
Once the cleaner is at the bottom of the pool and the power supply is connected, press the ON/OFF button on the power supply unit. The cleaner will begin its cleaning cycle automatically.
The Pulit Advance +5 operates in cycles of 1.5 to 2 hours, utilizing its Aquasmart electronic control system to efficiently clean the pool floor, walls, and waterline. The effective vibrating cleaning brush dislodges dirt from all surfaces.
Adjustable Suction Nozzles
The cleaner features height-adjustable suction nozzles to ensure perfect adaptation to any pool type, optimizing cleaning performance.
Maintenance
Cleaning Filter Cartridges
The Pulit Advance +5 features top-access filter cartridges, making them easy to clean without direct contact with dirt. A LED indicator on the power supply unit will illuminate when the filter needs cleaning.
- Disconnect the power supply unit from the electrical outlet.
- Remove the cleaner from the pool.
- Open the top access cover of the cleaner.
- Remove the filter cartridges.
- Rinse the cartridges thoroughly with a garden hose until all debris is removed.
- Reinsert the clean filter cartridges and close the top access cover.
Image: The AstralPool Pulit Advance +5 with its top filter compartments open, demonstrating the easy access for cleaning the filter cartridges.
Brush Maintenance
Periodically inspect the PVA brushes for wear and tear. Replace them if they show significant damage to ensure optimal cleaning performance.
Image: An underside view of the AstralPool Pulit Advance +5, clearly showing its PVA brushes and traction system, essential for effective pool cleaning.
Cable Management
After each use, carefully coil the self-floating cable to prevent tangling and damage. Store the cleaner and cable in a dry, shaded area.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Cleaner does not start | No power to unit; Cable not properly connected; Power supply unit malfunction. | Check power outlet; Ensure all cable connections are secure; Contact customer support if power supply unit is faulty. |
| Poor cleaning performance | Clogged filter cartridges; Worn brushes; Obstruction in suction nozzles. | Clean filter cartridges; Inspect and replace brushes if necessary; Check and clear suction nozzles. |
| Cleaner does not climb walls | Clogged filter; Air trapped in cleaner; Water chemistry imbalance (e.g., high calcium). | Clean filter; Tilt cleaner to release air bubbles; Check pool water chemistry. |
| Cable tangles | Improper cable deployment; Excessive cable length in pool. | Ensure cable is fully extended and untangled before placing cleaner; Only use necessary cable length. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | Pulit Advance +5 |
| Cleaning Area | Pool floor, walls, and waterline |
| Cleaning Cycle Time | 1.5 - 2 hours |
| Cable Length | 18 meters (self-floating) |
| Filter Type | Top-access filter cartridges (standard, fine, coarse) |
| Brushes | PVA brushes |
| Control System | Aquasmart electronic control |
| Dimensions (L x W x H) | 0.16 x 0.16 x 0.14 cm (Product only, not shipping dimensions) |
| Weight | 500 grams (Product only, not shipping weight) |
| Material | Plastic |
Warranty Information
Specific warranty terms and conditions for the AstralPool Pulit Advance +5 Robotic Pool Cleaner are typically provided at the point of purchase or within separate documentation included with the product. Please refer to your purchase receipt and the warranty card for details regarding coverage period, what is covered, and how to make a claim.
Note: The product description mentions "Information indisponible sur les pièces détachées" (Information unavailable on spare parts). This suggests that spare parts availability might not be guaranteed or easily accessible.
Customer Support
For technical assistance, spare parts, or warranty claims, please contact your authorized AstralPool dealer or visit the official AstralPool website for support contact information.
It is recommended to have your product model number (Pulit Advance +5) and purchase date available when contacting support.
