1. Product Overview
This manual provides instructions for the Wacker Neuson Rubber Shock Mount Set, part number 0130000. These shock mounts are essential components designed to reduce vibration and absorb shock in various Wacker Neuson plate compactors, ensuring stable operation and protecting other machine components from excessive wear.
Compatible Models: WP1550, WP1540, VP1550, VP1550aw, VP1340a, VP1340aw, VP2050, VP2050aw.
Image: A set of four Wacker Neuson rubber shock mounts. Each mount consists of a cylindrical rubber body with a metal threaded stud extending from one end and a threaded metal insert on the opposite end. The mounts are black rubber with a metallic core visible at the ends. A plastic bag labeled "ORIGINAL SPARE PARTS WACKER NEUSON" is visible in the background.
2. Installation (Setup)
Proper installation of the rubber shock mounts is crucial for the performance and longevity of your plate compactor. Always refer to your specific compactor's service manual for detailed, model-specific installation procedures and safety precautions.
2.1 Safety Precautions
- Ensure the plate compactor is turned off, cooled down, and disconnected from any power source (if applicable) before beginning installation.
- Wear appropriate personal protective equipment (PPE), including gloves and eye protection.
- Secure the compactor to prevent accidental movement during installation.
2.2 General Installation Steps
- Access: Locate the existing shock mounts on your plate compactor. These typically connect the engine/vibrator assembly to the base plate.
- Removal: Carefully unbolt and remove the old, worn, or damaged shock mounts. Note their orientation for correct reinstallation.
- Inspection: Inspect the mounting surfaces for any damage, corrosion, or debris. Clean as necessary.
- Installation of New Mounts: Position the new Wacker Neuson rubber shock mounts (part number 0130000) in the correct orientation.
- Fastening: Secure the new mounts using the appropriate bolts and torque specifications as outlined in your compactor's service manual. Ensure all fasteners are tightened to prevent loosening during operation.
- Verification: After installation, visually inspect all connections to ensure they are secure and the mounts are properly seated.
3. Function and Operation
The rubber shock mounts are passive components that play a critical role in the operational integrity of your plate compactor. They function as vibration isolators, absorbing the intense vibrations generated by the compactor's engine and vibratory mechanism. This isolation:
- Reduces Operator Fatigue: Minimizes the transfer of vibrations to the operator's handle.
- Protects Components: Prevents excessive vibration from damaging the engine, fuel tank, and other sensitive components.
- Ensures Performance: Helps maintain the intended vibratory action of the plate for effective compaction.
No specific operational steps are required for the shock mounts themselves, as their function is integral to the compactor's design. Ensure the compactor is operated according to its primary instruction manual.
4. Maintenance
Regular inspection of the rubber shock mounts is vital for maintaining the performance and safety of your Wacker Neuson plate compactor.
4.1 Inspection Schedule
- Before Each Use: Perform a quick visual check for obvious damage or looseness.
- Every 50 Operating Hours or Monthly: Conduct a thorough visual inspection.
4.2 Inspection Points
- Cracks or Tears: Look for any signs of cracking, tearing, or degradation in the rubber material.
- Deformation: Check for permanent compression, bulging, or other signs of rubber deformation.
- Looseness: Ensure the mounts are securely fastened and not loose.
- Corrosion: Inspect the metal components of the mounts for rust or corrosion.
If any of these issues are observed, the shock mounts should be replaced immediately to prevent further damage to the compactor and ensure operator safety.
5. Troubleshooting
Issues with shock mounts typically manifest as increased vibration or unusual noises during compactor operation.
| Symptom | Possible Cause | Solution |
|---|---|---|
| Excessive vibration felt by operator | Worn, cracked, or damaged shock mounts. | Inspect and replace all shock mounts as a set. |
| Unusual knocking or rattling noises | Loose or severely degraded shock mounts. | Tighten fasteners or replace shock mounts. |
| Engine or components appear to be shifting excessively | Failed or severely compromised shock mounts. | Immediately cease operation and replace all shock mounts. |
If troubleshooting does not resolve the issue, or if you are unsure about the condition of your shock mounts, consult a qualified service technician or contact Wacker Neuson support.
6. Specifications
| Attribute | Detail |
|---|---|
| Part Number | 0130000 |
| Manufacturer | Wacker Neuson |
| Material | Rubber |
| Color | Black |
| Item Weight (per set) | Approximately 2 pounds |
| Package Dimensions | Approximately 6 x 5 x 5 inches |
| ASIN | B00SI2U642 |
7. Warranty Information
For specific warranty details regarding the Wacker Neuson Rubber Shock Mount Set (part number 0130000), please refer to the official warranty documentation provided by Wacker Neuson or contact your authorized dealer or seller. Warranty terms and conditions may vary.
8. Support
If you require further assistance with the installation, maintenance, or troubleshooting of your Wacker Neuson rubber shock mounts, please contact:
- Your authorized Wacker Neuson dealer.
- The seller from whom you purchased the product.
- Wacker Neuson customer service (refer to the official Wacker Neuson website for contact information).
Always provide the part number (0130000) and the model of your plate compactor when seeking support.
