iJDMTOY 2-Pin Electronic LED Flasher Relay (LF1-S-PIN) Instruction Manual

1. Product Overview

The iJDMTOY 2-Pin Electronic LED Flasher Relay (LF1-S-PIN) is designed to resolve the hyper flash issue commonly encountered when upgrading incandescent turn signal bulbs to LED bulbs on motorcycles, bikes, and scooters. This electronic flasher unit provides a normal flash rate without the need for additional load resistors or complex wiring modifications.

Image 1.1: The iJDMTOY 2-Pin Electronic LED Flasher Relay (LF1-S-PIN) with its integrated wiring and connector.

2. Key Features

• Direct Replacement: Designed as a direct plug-in replacement for many OEM 2-pin flasher units.
• Hyper Flash Solution: Effectively eliminates the rapid flashing (hyper flash) that occurs when installing LED turn signal bulbs.
• Heat-Free Operation: Unlike load resistors, this electronic flasher generates minimal heat.
• IP67 Waterproof Design: Provides protection against dust and water ingress.
• Compact Size: Cubic design with approximate dimensions of 1.1 x 1.1 x 1.0 inches.

3. Compatibility

This 2-pin electronic LED flasher relay is compatible with a wide range of motorcycles, including models from Honda, Kawasaki, Suzuki, and Yamaha (e.g., R1, R6, FZ1, FZ6, FZ8, MT07, MT09), as well as many other brands of motorbikes and scooters.

Important Note: This LED flasher does not replace all flasher units. Before purchasing and installing, it is crucial to:

• Count the pin numbers on your existing flasher unit.
• Compare the shape, configuration, and size of your original flasher with the images provided in this manual and on the product page.

Image 3.1: Visual representation of the LF1-S-PIN flasher relay and its broad compatibility with motorcycle brands.

4. Installation Instructions

Installation of the iJDMTOY 2-Pin Electronic LED Flasher Relay is a straightforward process. Follow these steps:

1. Locate the Original Flasher: Identify the location of your motorcycle's original flasher unit. This is typically found under the dashboard, under the seat, or within the engine bay fuse box. Consult your vehicle's service manual if you are unsure.
2. Disconnect Power: For safety, turn off your motorcycle and disconnect the battery before proceeding with any electrical work.
3. Unplug Original Flasher: Carefully unplug the existing flasher unit from its harness.
4. Install New Flasher: Directly plug the iJDMTOY 2-Pin Electronic LED Flasher Relay into the vehicle's flasher harness. Ensure the connection is secure.
5. Secure the Flasher: If necessary, use a zip tie or other suitable method to secure the new flasher in place, especially if it does not fit perfectly into the original mounting bracket.
6. Reconnect Power: Reconnect your motorcycle's battery.
7. Test Functionality: Turn on your motorcycle and test the turn signals to ensure they flash at a normal rate.

Image 4.1: Demonstrates the physical comparison and replacement of the flasher relay in a motorcycle's wiring.

5. Operation

Once installed, the iJDMTOY 2-Pin Electronic LED Flasher Relay operates automatically. When the turn signal lever is activated, the relay will regulate the electrical current to the LED turn signal bulbs, ensuring they flash at the standard, intended rate, thereby eliminating the rapid flashing (hyper flash) that occurs due to the lower power draw of LED bulbs compared to incandescent bulbs.

Image 5.1: The flasher relay pictured with a motorcycle displaying properly functioning LED turn signals.

6. Troubleshooting

• Hyper Flash Persists:
  • Ensure the flasher is correctly installed and securely plugged in.
  • Verify that your motorcycle's original flasher was indeed a 2-pin unit and that the iJDMTOY flasher is compatible with your specific vehicle model.
  • Check for any loose connections in the turn signal circuit.
• Four-Way Flash Issue (All Signals Flash Simultaneously):
  • Some motorcycle models may exhibit a four-way flash when all turn signals are converted to LED. This flasher relay primarily addresses hyper flash for individual turn signals, not necessarily the four-way hazard function.
  • Potential solutions may involve leaving some incandescent bulbs in the system (e.g., rear turn signals) or installing diodes/resistors in specific parts of the turn signal circuit. Consult motorcycle-specific forums or a qualified technician for guidance on these advanced modifications.
• Delayed Flash Rate or Unusual Timing:
  • Some users have reported a slight delay (approximately 0.5 seconds) before the first flash, or a flash pattern where the light stays on longer and off for a shorter duration. This is a characteristic of some electronic flasher designs and is generally not indicative of a malfunction.
• Not Working on Specific Models (e.g., 2012 Ninja 1000):
  • Despite broad compatibility, some specific vehicle models may not be fully compatible. Always verify compatibility with your vehicle's original flasher specifications (pin count, shape, size) before installation.

7. Product Specifications

Image 7.1: The flasher relay showing its dimensions and a basic wiring schematic.

Image 7.2: Detailed view of the flasher relay with its physical dimensions indicated.

8. Support Information

For further assistance, technical support, or inquiries regarding the iJDMTOY 2-Pin Electronic LED Flasher Relay, please refer to the official iJDMTOY website or contact their customer service department. Specific warranty details may vary; please consult your purchase documentation or the iJDMTOY official channels for the most current warranty information.

You can visit the iJDMTOY store for more products and support: iJDMTOY Amazon Store