Raypak 014324F

Download PDF
Contents

Raypak 014324F Ignition Control Unit User Manual

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of the Raypak 014324F Ignition Control unit. This component is designed to provide reliable ignition and control for various heating system applications. Please read this manual thoroughly before proceeding with installation or operation.

2. Safety Information

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Read the installation, operating, and maintenance instructions thoroughly before installing or servicing this equipment.

  • Always disconnect electrical power to the heating system before installing or servicing the ignition control unit.
  • Installation and servicing must be performed by a qualified, licensed technician.
  • Ensure all wiring connections comply with local and national electrical codes.
  • Verify proper grounding of the heating system and the control unit.
  • Do not bypass any safety devices.

3. Product Overview

The Raypak 014324F is a multi-try ignition control module, identified by its part number 35-975900-111. It integrates various control functions for heating systems, including inputs for sensors, 24 VAC switches, and outputs for valves, blowers, and pumps. The unit is designed for robust performance in a range of ambient temperatures.

Raypak 014324F Ignition Control Unit, top view

Figure 1: Top view of the Raypak 014324F Ignition Control unit, showing various connection terminals and labels.

4. Setup and Installation

Installation of the Raypak 014324F Ignition Control unit requires careful attention to wiring and safety protocols. It is strongly recommended that installation be performed by a certified HVAC technician.

  1. Power Disconnection: Ensure all electrical power to the heating appliance is completely disconnected at the main circuit breaker before beginning any work.
  2. Mounting: Securely mount the control unit in the designated location within the heating appliance. Ensure it is protected from excessive heat, moisture, and vibration.
  3. Wiring Connections: Refer to the specific wiring diagram provided with your heating appliance and the labels on the control unit. Connect all wires to their corresponding terminals. Pay close attention to:
    • Input: 24VAC, 50/60 Hz (J6)
    • Valve: 120VAC (J7)
    • Blower: 120/240VAC (J8)
    • DHW Pump: 120VAC (J9)
    • Boiler Pump: 120VAC (J10)
    • Alarm Contact: 24VAC (J11)
    • Ignitor: 120VAC (Dedicated terminals)
    • Sensors: (J5)
    • 24 VAC Switches: (J4)
  4. Fuse Installation: The unit requires specific fuses. Use only type GMA fuses, 5A MAX.
  5. Grounding: Ensure the control unit and the heating appliance are properly grounded.
  6. Final Check: Double-check all wiring connections for tightness and correctness before restoring power.
Raypak 014324F Ignition Control Unit, angled view showing side connectors

Figure 2: Angled view of the control unit, highlighting the various terminal blocks for system integration.

5. Operating Instructions

Once the Raypak 014324F Ignition Control unit is correctly installed and wired, follow these general operating guidelines:

  1. Restore Power: Turn on the electrical power to the heating appliance at the main circuit breaker.
  2. System Initialization: The control unit will perform a self-check and initiate the ignition sequence as required by the heating system's thermostat or control panel.
  3. Monitor Operation: Observe the heating appliance for proper ignition and operation. The control unit manages the timing of ignition, gas valve opening, and blower operation.
  4. Fault Indicators: The unit may have an LED indicator for power, alarm, or fault conditions. Refer to the specific appliance manual for interpretation of these indicators.

6. Maintenance

The Raypak 014324F Ignition Control unit is designed for reliable, long-term operation with minimal maintenance. However, periodic checks can help ensure continued performance.

  • Visual Inspection: Annually, or during routine appliance servicing, visually inspect the control unit and its wiring for any signs of damage, corrosion, or loose connections.
  • Cleanliness: Keep the area around the control unit free from dust, debris, and moisture.
  • No User-Serviceable Parts: The internal components of the control unit are not user-serviceable. Do not attempt to open or repair the unit. If a malfunction occurs, the unit should be replaced by a qualified technician.

7. Troubleshooting

If the heating system experiences issues related to ignition or control, consider the following troubleshooting steps. Always ensure power is disconnected before inspecting wiring or components.

  • No Ignition:
    • Verify that the main power supply to the appliance is on.
    • Check for proper 24VAC input to the control unit.
    • Inspect the ignitor for damage or wear.
    • Ensure the gas valve is receiving power and opening correctly.
    • Check all wiring connections for tightness and continuity.
  • Intermittent Operation:
    • Check for loose wiring connections, especially to sensors.
    • Ensure proper grounding.
    • Inspect for environmental factors like excessive moisture or vibration.
  • Fault Indicator (LED): If the unit has a fault LED, consult the specific heating appliance's manual for diagnostic codes and their meanings.

If troubleshooting steps do not resolve the issue, contact a qualified service technician.

8. Specifications

The following table details the technical specifications for the Raypak 014324F Ignition Control unit:

FeatureSpecification
ManufacturerRaypak
Model Number014324F
Part Number35-975900-111
Input Voltage24VAC, 50/60 Hz, 400 mA
Valve Output120VAC, 5A MAX
Blower Output120/240VAC, 15A MAX
DHW Pump Output120VAC, 5A MAX
Boiler Pump Output120VAC, 5A MAX
Alarm Contact24VAC, 2A MAX
Ignitor Output120VAC, 5A
Ambient Temperature Range-40°F to +165°F
Item Weight2.08 ounces
Package Dimensions14 x 10 x 8 inches
ASINB00R8HDCIK
UPC682470447853

9. Warranty and Support

For specific warranty information regarding the Raypak 014324F Ignition Control unit, please refer to the documentation provided with your original purchase or visit the official Raypak website. For technical support, installation assistance, or to locate a certified service technician, please contact Raypak customer service directly.

Raypak Official Website: www.raypak.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.