1. Product Overview
The Permatex 81160 High-Temp Red RTV Silicone Gasket Maker is a specialized sealant designed for heavy-duty applications requiring resistance to extreme temperatures. This product forms reliable gaskets that can withstand intermittent temperatures ranging from -65°F to 650°F (-54°C to 343°C).
It is formulated to create durable, flexible, and waterproof seals for various automotive and industrial repair needs.
Image 1.1: Permatex 81160 High-Temp Red RTV Silicone Gasket tube. This image shows the product packaging, highlighting the brand, product name, and key features.
2. Safety Information
Always read and understand all safety precautions before using this product. Use personal protective equipment as required.
2.1. Precautionary Statements - Prevention
- Contains: Calcium carbonate, Iron oxide.
- Obtain special instructions before use.
- Do not handle until all safety precautions have been read and understood.
- Use personal protective equipment as required.
2.2. Precautionary Statements - Response
- IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists, get medical advice/attention.
- IF ON SKIN: Wash with plenty of soap and water. If skin irritation or rash occurs, get medical advice/attention. Wash contaminated clothing before reuse.
2.3. Precautionary Statements - Storage
- Protect from sunlight.
- Store in a well-ventilated place.
- Store locked up.
- Keep out of the reach of children.
3. Setup
3.1. Surface Preparation
For optimal results, ensure that all surfaces where the gasket maker will be applied are clean and dry. Remove any old gasket material, grease, oil, or other contaminants that could interfere with adhesion.
4. Application Instructions
- Prepare Nozzle: Cut the nozzle to the desired bead size.
- Apply Gasket Maker: Apply a continuous bead of silicone, approximately 1/16" to 1/4" (2 to 6mm) thick, to one surface. Ensure the bead surrounds all bolt holes.
- Assemble Parts: Immediately assemble the parts while the silicone is still wet.
- Initial Tightening: Finger tighten the assembly until the material begins to squeeze out around the flange.
Image 4.1: Example of Permatex 81160 High-Temp Red RTV Silicone Gasket application. This image illustrates the product being applied as a continuous bead on a surface.
5. Curing and Finishing
- Initial Dry Time: Allow the gasket maker to dry for one hour.
- Final Tightening: After the initial dry time, tighten the assembly to the manufacturer's specified torque.
- Full Cure Time: Allow 24 hours for the gasket maker to fully cure before filling with fluids or returning the component to service.
6. Maintenance
6.1. Product Storage
After each use, replace the cap securely to prevent the product from drying out. Store the tube in a cool, dry, well-ventilated area, away from direct sunlight and out of reach of children.
7. Troubleshooting and Limitations
Important Note: This product is NOT recommended for use on head gaskets or on parts that will come into direct contact with gasoline. Using the product in these applications may lead to product failure and potential damage.
8. Product Specifications
| Feature | Detail |
|---|---|
| Product Name | Permatex High-Temp Red RTV Silicone Gasket Maker |
| Model Number | 81160 |
| Brand | Permatex |
| Material | Silicone |
| Color | Red |
| Temperature Range (Intermittent) | -65°F to 650°F (-54°C to 343°C) |
| Full Cure Time | 24 Hours |
| Item Volume | 3 Fluid Ounces |
| Water Resistance Level | Waterproof |
| UPC | 686226811608 |
9. Disposal Information
Dispose of contents and container in accordance with local regulations and to an approved waste disposal plant. Do not dispose of in household waste.
10. Contact and Support
For further assistance or inquiries, please contact Permatex:
- Manufacturer: Permatex Chemicals, a division of ITW
- Address: Solon, OH 44139, USA
- Toll Free: 866-732-9502
- Website: www.permatex.com
Permatex and its design are trademarks of Illinois Tool Works Inc. The product is assembled in the U.S.A. with U.S. and global materials.
11. Warranty Information
Specific warranty details for Permatex products are typically available on the manufacturer's official website or by contacting their customer support directly. Please refer to www.permatex.com or call 866-732-9502 for the most current warranty information.