Stanley 298601 STAKP 310 MHz Wireless Keypad User Manual

1. Product Overview

The Stanley 298601 STAKP Wireless Keypad is a weather-resistant, keyless entry system designed for use with compatible Stanley 310 MHz garage door and gate openers. This keypad allows you to operate your opener by entering a personal identification number (PIN), providing convenient access without a remote control.

Image: Front view of the Stanley 298601 STAKP Wireless Keypad, featuring a numeric keypad (0-9) and 'RADIO LEARN' and 'ACCESS LEARN' buttons. The device is gray with 'MULTI-CODE' branding visible.

2. Setup and Installation

2.1 Battery Installation

The keypad requires batteries for operation. Ensure you use the correct type and polarity as indicated inside the battery compartment. Batteries are typically not included with the unit.

1. Locate the battery compartment cover on the back of the keypad.
2. Remove the cover.
3. Insert the required batteries, observing the correct positive (+) and negative (-) orientation.
4. Replace the battery compartment cover securely.

2.2 Mounting the Keypad

Choose a convenient location near your garage door or gate, out of reach of small children, and away from moving parts. The keypad should be mounted at a height that is easily accessible to all users.

1. Mark the desired mounting holes on the surface using the keypad as a template.
2. Drill pilot holes if necessary.
3. Secure the keypad to the surface using appropriate screws (not included).

2.3 Programming Your Keypad

This keypad is designed to be compatible with 310 MHz Stanley and Multi-Code garage door and gate openers. Programming involves setting a personal access code and linking the keypad to your opener's receiver.

Note: If your opener uses dip switches, ensure the keypad's internal dip switches (if present) match your opener's settings before proceeding with the steps below. Refer to your opener's manual for its specific dip switch configuration.

1. Set your Personal Identification Number (PIN): Press the 'ACCESS LEARN' button once. Enter your desired 1 to 6 digit PIN. Press 'ACCESS LEARN' again to save.
2. Activate Learning Mode on your Opener: Locate the 'Learn' or 'Smart' button on your garage door or gate opener's motor head. Press and release this button. The indicator light on the opener will typically illuminate, signaling it is in learning mode for a short period (usually 30 seconds).
3. Transmit Signal from Keypad: Within the learning mode timeframe, enter your programmed PIN on the keypad, then press the 'RADIO LEARN' button.
4. Confirm Programming: The opener's light may flash or click, indicating successful programming. Test the keypad by entering your PIN and pressing 'RADIO LEARN'. The opener should activate.
5. Multiple Openers (if applicable): If you have multiple openers, repeat the programming steps for each opener, ensuring each has a unique PIN or is programmed to the correct 'RADIO LEARN' channel if the keypad supports multiple channels.

If programming fails, ensure the batteries are fresh, the keypad is within range of the opener, and you are following the steps correctly. Consult your opener's manual for specific learning mode instructions.

3. Operating Instructions

To operate your garage door or gate opener using the Stanley 298601 STAKP Wireless Keypad:

1. Approach the keypad.
2. Enter your previously programmed Personal Identification Number (PIN).
3. Press the 'RADIO LEARN' button.

The garage door or gate opener should activate, performing its programmed function (e.g., opening, closing, or stopping).

4. Maintenance

4.1 Battery Replacement

When the keypad's performance degrades or the indicator light (if present) signals low battery, it is time to replace the batteries. Follow the battery installation steps in Section 2.1.

4.2 Cleaning

Clean the keypad's exterior with a soft, damp cloth. Avoid using abrasive cleaners or solvents, as these can damage the finish or internal components.

5. Troubleshooting

• Keypad not responding:
  • Check batteries. Replace if necessary.
  • Ensure the keypad is within operational range of the opener.
  • Verify that the keypad is correctly programmed to your opener. Repeat programming steps if unsure.
• Incorrect code entered:
  • Re-enter your PIN carefully.
  • If you have forgotten your PIN, you may need to reset and reprogram the keypad (refer to programming instructions).
• Buttons feel sticky or unresponsive:
  • This may indicate wear or internal damage. If cleaning does not resolve the issue, the unit may require replacement.
• Keypad does not work with my Stanley opener:
  • Confirm your opener operates on the 310 MHz frequency.
  • Ensure your opener is compatible with Multi-Code or Stanley 310 MHz systems. Some older Stanley openers with dip switches may require specific compatibility.
  • Verify that any internal dip switches on the keypad (if applicable) match your opener's settings.

6. Specifications

• Model Number: 298601
• Manufacturer: Linear
• Frequency: 310 MHz
• Compatibility: Stanley and Multi-Code 310 MHz garage door and gate openers
• Power Source: Batteries (not included)
• Item Package Quantity: 1
• Date First Available: August 5, 2013

7. Warranty and Support

Specific warranty information for the Stanley 298601 STAKP Wireless Keypad is not provided within this document. For details regarding warranty coverage, technical support, or replacement parts, please contact the manufacturer, Linear, or your product retailer directly.