Anker AK-A1405011 iPhone 6/6s Battery Case User Manual

1. Product Overview

The Anker AK-A1405011 is an ultra-slim extended battery case designed specifically for the iPhone 6 and iPhone 6s (4.7-inch models). This MFi certified case provides both protection for your device and an additional 2850mAh battery capacity, offering approximately 120% extra battery life to extend your phone's usage throughout the day.

Its design features a matte rubber material for improved grip and recessed buttons to prevent accidental presses. The case allows for independent charging, meaning you can charge the case's battery separately from your iPhone's internal battery.

2. Package Contents

• Anker AK-A1405011 iPhone 6/6s Battery Case
• Micro USB Charging Cable
• Headphone Jack Extender (if included by manufacturer)
• User Manual (this document)

3. Product Components

Figure 1: Anker AK-A1405011 iPhone 6/6s Battery Case. This image displays the sleek, black battery case designed for the iPhone 6/6s, highlighting its form factor and integrated design.

• Power Button/LED Indicators: Located on the lower back of the case. Press once to check battery level (LEDs light up). Press and hold to activate/deactivate charging to the iPhone.
• Micro USB Charging Port: Located at the bottom of the case for charging the case's internal battery.
• Lightning Connector: Internal connector that plugs into your iPhone's charging port.
• Audio Jack Opening: Designed to accommodate the iPhone's headphone jack. An extender may be required for some headphone plugs.

4. Setup and Installation

1. Separate the Case: Gently remove the top cap of the battery case by sliding it upwards.
2. Insert iPhone: Slide your iPhone 6 or 6s into the battery case, ensuring the iPhone's Lightning port properly connects with the case's internal Lightning connector. Push the iPhone down until it is securely seated.
3. Reattach Top Cap: Slide the top cap back onto the case until it clicks into place, securing your iPhone within the case.

5. Operation

5.1 Charging Your iPhone

• To begin charging your iPhone from the battery case, press and hold the power button on the back of the case for approximately 2-3 seconds. The LED indicators will illuminate, and your iPhone will show that it is charging.
• To stop charging your iPhone, press and hold the power button again for 2-3 seconds. The LED indicators will turn off, and your iPhone will cease charging from the case.

5.2 Checking Battery Level

Briefly press the power button on the back of the case. The LED indicators will light up to show the remaining battery capacity of the case:

• 4 LEDs: 75-100% charged
• 3 LEDs: 50-75% charged
• 2 LEDs: 25-50% charged
• 1 LED: 0-25% charged

6. Charging the Battery Case

1. Connect the supplied Micro USB cable to the charging port at the bottom of the battery case.
2. Connect the other end of the Micro USB cable to a USB wall adapter or a computer's USB port.
3. The LED indicators on the back of the case will flash to indicate charging progress. All four LEDs will remain solid when the case is fully charged.
4. When the iPhone is installed in the case and the case is connected to power, both the iPhone and the case will charge simultaneously. To charge only the case while the iPhone is installed, press and hold the power button on the case to stop charging the iPhone, then connect the case to power.

7. Maintenance

• Keep the case clean and free from dust and debris. Use a soft, dry cloth for cleaning.
• Avoid exposing the case to extreme temperatures, direct sunlight, or high humidity.
• Do not attempt to disassemble or modify the case, as this will void the warranty and may cause damage.
• Handle the case with care to prevent drops or impacts, which could damage both the case and your iPhone.

8. Troubleshooting

• iPhone not charging from case:
  • Ensure the iPhone is properly seated and connected to the case's internal Lightning connector.
  • Verify the battery case has sufficient charge by briefly pressing the power button.
  • Activate charging by pressing and holding the power button for 2-3 seconds.
• Battery case not charging:
  • Check if the Micro USB cable is securely connected to both the case and the power source.
  • Try using a different Micro USB cable or power adapter to rule out cable/adapter issues.
  • Ensure the power outlet is functional.
• Accidental charging activation:
  • The power button is designed to be recessed to minimize accidental presses. If it activates unintentionally (e.g., in a pocket), ensure the phone is oriented such that the button is not subjected to constant pressure.
• "Accessory not supported" message:
  • Although the case is MFi certified, this message can sometimes appear. Try removing and reinserting the iPhone into the case.
  • Ensure the Lightning connector on your iPhone and the case's internal connector are clean and free of debris.
  • If the issue persists, contact Anker customer support.

9. Specifications

10. Warranty and Customer Support

Anker products are backed by a limited warranty. For detailed warranty information, product registration, and customer support, please visit the official Anker website or contact their customer service team. Please have your product model number (AK-A1405011) and proof of purchase available when seeking support.

You can typically find contact information and FAQs on the Anker Store on Amazon or their official website.