Everbilt 1/4 HP Submersible Sump Pump with Tether User Manual

Introduction

This manual provides detailed instructions for the safe and efficient operation, installation, and maintenance of your Everbilt 1/4 HP Submersible Sump Pump with Tether. Designed for durability with reinforced aluminum housing, this pump is suitable for 14-inch basins and larger, offering reliable water removal for your home. Please read this manual thoroughly before installation and operation to ensure proper use and to prevent injury or damage.

Important Safety Information

Always follow basic safety precautions when installing, operating, or maintaining this product to reduce the risk of fire, electric shock, and personal injury.

• Electrical Safety: Ensure the pump is connected to a properly grounded outlet. Do not remove the grounding prong. Do not use extension cords.
• Water and Electricity: Never handle the pump or its power cord with wet hands or while standing in water. Always disconnect power before servicing.
• Submersible Use Only: This pump is designed for submersible use in water only. Do not use it for flammable liquids, corrosive chemicals, or in dry conditions.
• Temperature Limits: Do not pump water hotter than 104°F (40°C).
• Children and Pets: Keep children and pets away from the sump pit area.
• Proper Installation: Ensure the pump is installed in a basin of adequate size (14 inches or larger) to allow for proper float switch operation.

Package Contents

Before beginning assembly or installation, ensure all parts are present and accounted for. If any parts are missing or damaged, do not attempt to install or operate the pump. Contact customer service for assistance.

• Everbilt 1/4 HP Submersible Sump Pump with Tether
• User and Care Guide (this manual)

Image shows the Everbilt 1/4 HP Submersible Sump Pump, its retail packaging, and the included Use and Care Guide. The pump is black with a tethered float switch and power cord. The box highlights key features such as 1/4 HP, 3,000 gallons per hour capacity, and a 1-year warranty.

Setup and Installation

Proper installation is crucial for the efficient and safe operation of your sump pump. Follow these steps carefully:

1. Basin Preparation: Ensure your sump basin is clean and free of debris. The basin should be at least 14 inches in diameter to allow for proper float switch operation.
2. Pump Placement: Place the pump on a solid, level surface at the bottom of the sump basin. Avoid placing it directly on dirt or gravel, which can clog the intake.
3. Discharge Pipe Connection: Connect a discharge pipe (typically 1-1/4 inch or 1-1/2 inch PVC pipe) to the pump's discharge port. Use a check valve (not included) in the discharge line to prevent water from flowing back into the basin when the pump shuts off.
4. Tether Switch Adjustment: The tethered float switch controls the pump's on/off cycles. Adjust the tether length to ensure the pump turns on before water reaches a critical level and turns off after the water is sufficiently removed, without running dry. Ensure the float can move freely without obstruction.
5. Electrical Connection: Plug the pump's power cord into a dedicated, grounded 120V AC outlet. Do not use extension cords or adapters. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI).
6. Test Operation: Fill the sump basin with water to verify the pump turns on and off correctly as the water level rises and falls. Check for any leaks in the discharge line.

Operating Instructions

The Everbilt 1/4 HP Submersible Sump Pump operates automatically via its tethered float switch. Once properly installed and plugged in, the pump will activate when the water level in the sump basin rises, causing the float switch to lift. It will continue to pump water out until the water level drops, allowing the float switch to fall and deactivate the pump.

Regularly inspect the sump basin and pump for any obstructions or debris that could interfere with the float switch or pump operation.

Maintenance

Routine maintenance helps ensure the longevity and reliable performance of your sump pump.

• Monthly Inspection: Periodically check the sump basin for accumulated dirt, silt, or debris that could clog the pump's intake screen or interfere with the float switch. Clean as necessary.
• Float Switch Check: Manually lift the float switch to ensure it activates the pump. Ensure it moves freely without sticking.
• Discharge Line: Inspect the discharge pipe for any blockages or leaks. Ensure the check valve is functioning correctly.
• Winterization (if applicable): If the pump is in an area subject to freezing temperatures and will not be used, disconnect it, clean it thoroughly, and store it in a warm, dry place to prevent freezing damage.
• Power Cord: Inspect the power cord for any signs of damage or fraying. Do not use the pump if the cord is damaged.

Troubleshooting

Refer to the table below for common issues and their potential solutions.

Specifications

Warranty and Support

Warranty: This Everbilt sump pump comes with a 1-Year Limited Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

Customer Support: For questions, problems, or missing parts, please contact Everbilt Customer Service before returning to the store. Customer service is available Monday-Friday, 8 a.m. - 6 p.m. EST.

Phone: 1-844-241-5521

Website: HOMEDEPOT.COM

Thank you for choosing Everbilt. We appreciate the trust and confidence you have placed in our submersible sump pump. We strive to continually create quality products designed to enhance your home.