1. Introduction
This manual provides essential information for the installation, operation, and maintenance of your PROFLO PF5114HE Jerrit Toilet Tank. This product is designed as a tank-only configuration, allowing you to pair it with a compatible toilet bowl. Please read these instructions thoroughly before proceeding with installation or use to ensure proper function and longevity of the product.
2. Safety Information
Please observe the following safety precautions:
- Always wear appropriate personal protective equipment (PPE) such as gloves and eye protection during installation.
- Handle ceramic components with care to prevent chipping or breakage.
- Ensure all water supply lines are turned off before beginning installation.
- If you are unsure about any step, consult a qualified plumber.
- Do not overtighten connections, as this may cause damage.
3. Package Contents
The PROFLO PF5114HE Jerrit Toilet Tank package includes:
- PROFLO PF5114HE Jerrit Toilet Tank (White)
- Internal tank components (fill valve, flush valve, trip lever)
- Tank-to-bowl hardware (bolts, washers, nuts, gasket)
Note: This product is a tank-only configuration. A toilet bowl and toilet seat are not included and must be purchased separately.
4. Setup and Installation
This section outlines the general steps for installing the PROFLO PF5114HE Jerrit Toilet Tank onto a compatible toilet bowl. Professional installation is recommended.
4.1 Preparation
- Ensure the water supply to the toilet area is turned off.
- Remove any existing toilet tank and clean the top surface of the toilet bowl where the tank will sit.
- Inspect the new tank for any visible damage.
4.2 Tank-to-Bowl Assembly
- Place the large rubber tank-to-bowl gasket over the flush valve opening on the underside of the tank. Ensure it is seated properly.
- Carefully align the tank with the bolt holes on the back of the toilet bowl.
- Insert the tank-to-bowl bolts through the tank and the bowl holes.
- From underneath the bowl, place washers and nuts onto the bolts. Hand-tighten initially.
- Alternately tighten the nuts with a wrench, ensuring the tank is level and stable. Do not overtighten to avoid cracking the ceramic.
Figure 1: Front view of the PROFLO PF5114HE Jerrit Toilet Tank. This image shows the tank with its lid and flush lever, ready for installation onto a toilet bowl.
4.3 Water Supply Connection
- Connect the flexible water supply line from the wall shut-off valve to the fill valve shank on the underside of the tank. Hand-tighten, then use a wrench for a final quarter-turn. Do not overtighten.
- Slowly turn on the water supply valve. Check for leaks at all connections.
- Allow the tank to fill. The fill valve will automatically shut off when the water level reaches the designated line inside the tank.
Figure 2: The PROFLO PF5114HE Jerrit Toilet Tank shown installed on a compatible toilet bowl. This illustrates the complete assembly of the tank and bowl.
5. Operating Instructions
The PROFLO PF5114HE Jerrit Toilet Tank operates with a standard flush mechanism. To flush the toilet:
- Press down firmly on the flush lever located on the front of the tank.
- Hold the lever down briefly until the water in the tank begins to empty into the bowl.
- Release the lever. The tank will then refill automatically to the proper water level.
This tank is designed for a 1.28 gallons-per-flush (GPF) flow rate, ensuring efficient water usage.
6. Maintenance
6.1 Cleaning
- Clean the exterior of the tank with a soft cloth and mild, non-abrasive cleaner.
- Avoid using harsh chemicals, abrasive pads, or strong detergents, as these can damage the finish.
- For internal cleaning, periodically inspect the fill valve and flush valve for mineral buildup. If necessary, turn off the water supply, drain the tank, and gently clean components with a soft brush.
6.2 Component Inspection
- Regularly check the tank-to-bowl connection for any signs of leaks.
- Inspect the flapper or flush valve seal for wear. A worn seal can cause continuous running water.
- Ensure the fill valve is functioning correctly and the water level is set appropriately.
7. Troubleshooting
Here are solutions to common issues you might encounter:
| Problem | Possible Cause | Solution |
|---|---|---|
| Tank leaks at base | Loose tank-to-bowl bolts, worn gasket | Gently tighten tank-to-bowl bolts. If leak persists, replace the tank-to-bowl gasket. |
| Toilet runs continuously | Worn flapper/flush valve seal, misaligned fill valve, incorrect water level | Inspect and replace flapper/seal if worn. Adjust fill valve to ensure proper water level. Check for obstructions. |
| Weak or incomplete flush | Low water level, clogged siphon jet in bowl (not tank issue), flapper closing too quickly | Adjust water level higher in tank. Ensure flapper stays open long enough. Consult bowl manual for siphon jet cleaning. |
| Tank does not fill | Water supply off, clogged fill valve, faulty fill valve | Check water supply valve. Clean or replace fill valve if necessary. |
If these steps do not resolve the issue, please contact PROFLO customer support or a qualified plumber.
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | PF5114HE |
| Color | White |
| Product Dimensions (D x W x H) | 19" x 18" x 14" |
| Material | Plastic (internal components), Ceramic (tank body) |
| Item Weight | 35.01 Pounds |
| Installation Type | Floor Mounted (tank to bowl) |
| Flow Rate | 1.28 gallons-per-flush (GPF) |
| UPC | 781889237168 |
9. Warranty and Support
For warranty information, technical assistance, or to purchase replacement parts, please contact PROFLO customer support directly. Refer to the official PROFLO website or your purchase documentation for specific contact details and warranty terms applicable to your region.
When contacting support, please have your model number (PF5114HE) and date of purchase readily available.
