Introduction
Figure 1: The SYLVANIA 48" T8 Octron Fluorescent Ecologic Lamp, shown in its retail packaging.
This manual provides essential information for the safe and effective installation, operation, and maintenance of your SYLVANIA 48" T8 Octron Fluorescent Ecologic Lamp. These lamps are designed to provide exceptional color rendering with a 90 CRI, making them suitable for color-critical applications, and offer outstanding value. For optimal performance and longevity, please read and follow all instructions carefully.
Product Specifications
| Specification | Value |
|---|---|
| Model Number | 22433 |
| Lamp Type | T8 Octron Fluorescent Ecologic Lamp |
| Wattage | 32 Watts |
| Length | 48 inches |
| Base Type | Bi-Pin Base (G12) |
| Lumen Output | 2450 Lumens |
| Color Temperature | 4100K (Cool White) |
| Color Rendering Index (CRI) | 90 |
| Average Lifetime (Instant Start) | Up to 22,500 hours |
| Average Lifetime (Programmed Start) | Up to 27,000 hours |
| Voltage | 120 Volts |
| Indoor/Outdoor Usage | Indoor, Outdoor |
Safety Information
Always turn off power at the circuit breaker before installing or removing fluorescent lamps. Handle lamps by the ends to avoid damaging the glass or internal components. Do not use in dimming circuits unless specifically rated for dimmable fluorescent lamps and compatible ballasts. Dispose of lamps according to local regulations, as they contain small amounts of mercury.
Setup and Installation
- Power Disconnection: Before beginning installation, ensure the power to the fixture is completely turned off at the circuit breaker or fuse box. Verify power is off using a voltage tester.
- Remove Old Lamp (if applicable): Carefully twist the old fluorescent tube 90 degrees to align the pins with the slots in the lampholders. Gently pull the lamp straight out from the fixture.
- Inspect Fixture: Check the lampholders for any damage or corrosion. Ensure they are clean and in good working order. Confirm the fixture uses a compatible T8 ballast (Rapid Start or Instant Start).
- Install New Lamp: Hold the new SYLVANIA T8 lamp by its ends. Align the pins on both ends of the lamp with the slots in the lampholders. Gently push the lamp into the lampholders until the pins are fully seated.
- Secure Lamp: Rotate the lamp 90 degrees until it locks securely into place. The lamp should feel firm and not wobble.
- Restore Power: Once the lamp is securely installed, restore power to the fixture at the circuit breaker.
- Test Operation: Turn on the light switch to confirm the lamp illuminates properly.
Figure 2: A bare SYLVANIA T8 fluorescent tube, illustrating its cylindrical shape and bi-pin connectors at each end, ready for installation.
Operating Instructions
SYLVANIA T8 Octron Fluorescent Ecologic Lamps are designed for straightforward operation in compatible fluorescent fixtures. Once installed, simply activate the light switch connected to the fixture. The lamp will illuminate rapidly, providing consistent, high-quality light.
- Ensure the fixture's ballast is compatible with T8 fluorescent lamps for optimal performance and lamp life.
- Avoid frequent on/off cycling, as this can reduce the lamp's lifespan.
- These lamps are suitable for both rapid and instant start ballasts, offering a long rated life under typical operating conditions.
Maintenance
Minimal maintenance is required for your SYLVANIA T8 fluorescent lamp. Regular cleaning and proper handling will help ensure its long-term performance.
- Cleaning: Periodically, with the power off and the lamp cool, gently wipe the lamp surface with a soft, dry, lint-free cloth to remove dust and debris. Do not use abrasive cleaners or solvents.
- Lamp Replacement: Replace lamps when they begin to flicker, dim significantly, or fail to illuminate. Always replace with a lamp of the same type and wattage for consistent light output and compatibility with the existing ballast.
- Fixture Inspection: Annually inspect the fixture wiring and lampholders for any signs of wear, damage, or loose connections.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not light up. |
|
|
| Lamp flickers or dims. |
|
|
| Ends of lamp are dark. |
|
|
Warranty and Support
For warranty information and technical support regarding your SYLVANIA T8 Octron Fluorescent Ecologic Lamp, please refer to the official LEDVANCE website or contact their customer service. The product warranty details can typically be found at www.sylvania.com.
For additional product information or to explore other lighting solutions, visit the LEDVANCE Store on Amazon: LEDVANCE Store.
Disposal Information
Fluorescent lamps contain a small amount of mercury and should be disposed of responsibly. Do not dispose of lamps in regular household trash. Please check with your local waste management authority for proper recycling or disposal options in your area. Many retailers and recycling centers offer collection programs for fluorescent lamps.
